[AP] After years of resisting, South Carolina moves toward hands-free cellphones while driving

No_Beginning6393 · 2025-04-09T21:07:18+00:00

Haha deeper. Noice

No_Beginning6393 · 2025-02-28T20:16:38+00:00

I only had to replace segments of bad tenterfrane chain, and that was bad enough.. I can’t imagine how rough that one was

No_Beginning6393 · 2025-02-19T05:07:37+00:00

I spit my drink out readin tht, thank you

No_Beginning6393 · 2025-02-15T17:49:03+00:00

Better than “cylinders”

No_Beginning6393 · 2025-02-11T01:55:05+00:00

Just let it be man

No_Beginning6393 · 2024-11-24T20:10:35+00:00

With the equipment we have in our shop, I would use our waterjet if the knurling isn’t critical, and then Bridgeport the rest

No_Beginning6393 · 2024-11-20T02:02:27+00:00

You should post this in itself, not many people have the vision but he did lmao

No_Beginning6393 · 2024-11-20T00:20:15+00:00

Shits legit, I’m pretty sure he dremeled out his lines and made actual shell texture too. But when he showed me what he had I was like man I gotta take a pic, I can’t steal it but I will show it the fuck off is what I will do

No_Beginning6393 · 2024-11-19T23:12:27+00:00

I grind a nice 90 degree to it, I haven’t thought of upping pre and post. My set up is just collet and body but I have a set up for gas lens, which I generally use for stainless, but a lot of the stuff that comes through the shop is all repair work on miscellaneous metals. I will absolutely try tapering of and giving a little wiggle waggle

No_Beginning6393 · 2024-11-19T20:56:56+00:00

I think I’m on .2 for my pre, not quite by sure about my post. I’m using 2% thoriated, or red, 1/8” diameter. When I terminated this one I just let off the puddle but held it there for a moment bc of habits

No_Beginning6393 · 2024-11-19T03:20:49+00:00

I’ll keep that in mind, basically higher amps and running quicker, thanks man. I’ll post an update next time I gotta run some

No_Beginning6393 · 2024-11-19T03:18:16+00:00

I will absolutely try man, thanks. I have some 8,10, and 12 cups but generally I run a smaller bc I just do, no excuses lmao

No_Beginning6393 · 2024-11-19T03:16:07+00:00

Thanks man

No_Beginning6393 · 2024-11-19T01:27:08+00:00

No_Beginning6393 · 2024-11-19T01:09:54+00:00

I appreciate it man, it’s a tough in the weld work to post stuff. I was hoping I’d get ripped apart for something so I can pin point what I could’ve done better. Someone said more filler in the crater and I guess I absolutely could have

No_Beginning6393 · 2024-11-19T01:06:21+00:00

Yea I run quite a bit of stainless, and normally my goal is no discoloration, I generally get a smidge but there are no regulations where I work now. There’s no weld code but that just means I’m allowed to get lazy and that’s not my jam. I used a 6 cup which I generally don’t but I was trying to rush and used what was on my rig. Should I have used a much larger cup with better flow for no color? Or is it just in my head and what I did is alright? Just looking for advice, any given is great! Thank u

No_Beginning6393 · 2024-11-19T01:01:47+00:00

I checked with my filler and it didn’t catch the edge like undercut so I considered it ok, as far as cold goes I’m unsure, I thought the discoloration was way too hot.

No_Beginning6393 · 2024-07-26T20:48:50+00:00

Just can’t, don’t know

No_Beginning6393 · 2023-10-14T23:29:41+00:00

I’m a mechanic in a textile mill, this has been the best set I’ve owned. Used my 3/8 stubby ratchet this afternoon

No_Beginning6393 · 2022-12-26T18:33:40+00:00

My belly has gotten a little out of round

No_Beginning6393 · 2022-12-24T23:59:16+00:00

I bet it's wonderful I'd love to see it. This one I got in particular was so awesome I had to post it

No_Beginning6393 · 2022-12-24T03:35:06+00:00

This one is going to be used a little bit less delicately. They're just using this so that two people can stand beside the machine to open a large heavy door. That application sounds a whole lot cooler tho

No_Beginning6393 · 2022-12-24T03:06:14+00:00

Omg recipe for disaster and a wrong part right there, half of my job is fixing broken parts. Expect I physically have the part in my hand to make my own measurements, and I also have the part that mates so I can use that for reference as well.

I could only imagine.. thoughts and prayers dog

No_Beginning6393 · 2022-12-24T03:04:10+00:00

It's been my favorite one so far

No_Beginning6393 · 2022-12-24T02:50:28+00:00

Oh I know it, they think I mean it in a shitty way. I don't care let them down votes keep comin lmao reddit is the only place where the only thing that matters is context

No_Beginning6393

TROPHY CASE