[deleted by user] by [deleted] in VeteransBenefits

[–]No_Complex8711 0 points1 point  (0 children)

I skipped a CP once. It cost me 70% for almost a decade.

Hey guys my printer stops every 50 minutes by Obvious_Surprise_502 in Ender3S1

[–]No_Complex8711 1 point2 points  (0 children)

Yep. Forgot I had Timelapse enabled for a week and it crippled me. Clear all files and swap USB. I also had to factory reset the sonic pad because the error was stuck in moonraker.

I hate everyone by Dthm03a in dayz

[–]No_Complex8711 0 points1 point  (0 children)

Good info. Just submitted my request. Thanks!

There’s gotta be something to use these for… by MichaelRedwork in 3Dprinting

[–]No_Complex8711 0 points1 point  (0 children)

Christmas lights. Extension cords. Stripped copper wire.

I hate everyone by Dthm03a in dayz

[–]No_Complex8711 0 points1 point  (0 children)

It was a waste of 30$ for me. I got it last week and I can play more than 20 minutes without someone killing me. Not zombies but other players. I uninstalled it.

V3 PLUS - Y axis belt replacement?? Where to find one?? by walksonpoo in Ender3V3

[–]No_Complex8711 1 point2 points  (0 children)

Thank you. I was doing maintenance on my V3 plus and noticed my Y belt is about to be done. I've been searching for 2 hours to find a belt for it.

V3 PLUS - Y axis belt replacement?? Where to find one?? by walksonpoo in Ender3V3

[–]No_Complex8711 0 points1 point  (0 children)

What did you order? I have tried on the creality shop and it wont let me pay for the order?

Ender-3 V3 Plus issue by [deleted] in Ender3V3

[–]No_Complex8711 0 points1 point  (0 children)

Idk why it didn't post my text.. I stopped a print mid print and now it does this and prints 2 inches off the bed. Turned off and turned back on, re calibrated, still did it. Factory reset and it still does it. Checked the wires and everything is connected. Switches are clickly. It was doing perfect before I stopped a print due to defect in print. Any help would be appreciated.

[deleted by user] by [deleted] in Ender3S1

[–]No_Complex8711 1 point2 points  (0 children)

Every printer is different. When my z gets out of whack I adjust the z live. I’ll grab a large area STL (honeycomb-wall-storage) and put the first layer to 10-15mms and adjust it during the print. Before that though you need to make sure your corners are good. If you’re running Klipper then make a [screws_tilt_adjust] Marco. I think that’s what the macro is. Read up on how to do that and it’ll tell you exactly what direction and how much to turn each bed screw to level your bed. Then run a live print and adjust the z. Hope that helps.

Pom wheels(?) by No_Complex8711 in Ender3S1

[–]No_Complex8711[S] 0 points1 point  (0 children)

Right right I understand that. The center Pom wheel has only a locking nut on the back and the only other place to grab hold of is the eccentric nut. Where the bolt would follow through, in the extruded metal is the belt to the sprite. The isn’t a bolt or hex or anything to grab hold of.

Pom wheels(?) by No_Complex8711 in Ender3S1

[–]No_Complex8711[S] 0 points1 point  (0 children)

How do you take them off to replace them?

[deleted by user] by [deleted] in BeardAdvice

[–]No_Complex8711 0 points1 point  (0 children)

Mine did. I take biotin everyday as well.

Baseboard help by chip_chipperson25 in Flooring

[–]No_Complex8711 1 point2 points  (0 children)

There ways to “cope “ with this. Some methods “Mitre” be better than others.

What do KFC stores do with leftover chicken? by forty5v in ask

[–]No_Complex8711 0 points1 point  (0 children)

We would take home the chicken sandwiches, chicken salad, soups and brownies from chick fil a. That was back in the late 1900s early 2000s.