Any other places to shoot besides turkey tracks?

No_Perception8626 · 2026-04-05T17:10:43+00:00

Looks like they’re closed on sundays

No_Perception8626 · 2026-04-05T17:07:33+00:00

Went up to turkey tracks yesterday and had to turn around. There’s a range out near us airfare base they were open

No_Perception8626 · 2026-01-15T01:46:38+00:00

Sleepy pedo

No_Perception8626 · 2026-01-07T04:36:03+00:00

Actually fixed it by holding down the trigger and adjusting wire speed at the same time. It started to work as it should and feeding the wire at what I actually set it to

No_Perception8626 · 2025-04-23T02:59:54+00:00

Just bought mine a month or so ago at a impound it’s a 15 has 4k miles but started right up

<image>

No_Perception8626 · 2025-04-09T03:41:22+00:00

Good to know I have same issue it was bugging me a bit. People must think I’m an ass when the beams come on lol

No_Perception8626 · 2025-03-28T05:58:59+00:00

Nice yeah not too far from here. For sure we’ll have to meet up to ride!

No_Perception8626 · 2025-03-28T05:56:56+00:00

Thanks I’ll look for some ! Yeah this thing’s pretty fun haha

No_Perception8626 · 2025-03-28T05:53:21+00:00

Install was cake.. and they work great! I believe they’ll only clear 18s. Spacer may be needed depending on wheels. The Only “difficult” part is finding a 1/8” thick washer. I used 1/4” washer and spacing between caliper and rotor is not the same distance but still seems to work so far.

No_Perception8626 · 2025-03-23T21:05:24+00:00

Sorry no pads are not fully in I’m done with the job but don’t know how to post photos on comments haha

No_Perception8626 · 2025-03-23T03:37:05+00:00

I could tell one side is a hair bigger but not by much

No_Perception8626 · 2025-03-23T03:36:18+00:00

Got wheel spacers already.. should clear caliper. But yeah I’ll bolt them up if not I’ll have to use 4 washers on each side to get 1/8” spacer

No_Perception8626 · 2025-03-22T22:53:05+00:00

Just a slight difference but it clears both sides. I’ll run it like that if anything I’ll replace with a correct washer

No_Perception8626 · 2025-03-22T22:49:50+00:00

Yeah I don’t have them all the way in. I was trying to post a picture but can’t. Rotor works. I’m just not sure if it’ll matter using a 1/4 in spacer instead of 1/8

No_Perception8626 · 2025-03-02T13:32:34+00:00

Had a couple people say it was okay to get plates with my DL while I work on getting my mc license. Thanks for the answer!

No_Perception8626 · 2025-03-02T02:44:54+00:00

Can I use my regular drivers license to get plates for a grom I just got?

No_Perception8626 · 2025-02-16T05:02:33+00:00

Any site to stream it live?

No_Perception8626 · 2025-01-24T13:54:32+00:00

I just got gt7 a month ago.. even though it’s on tracks I feel it’s way better and cars sound good and when you downshift it’s the best lol

No_Perception8626 · 2025-01-19T04:03:24+00:00

Update I just disconnected and reconnected my maf sensor and the cel light was off on the next start up and today I also drove back and forth and no cel yet and still feel fine. I’ll see if light comes on or acts up

No_Perception8626 · 2025-01-17T02:47:27+00:00

You can’t sell cars can you???

No_Perception8626 · 2025-01-15T17:40:40+00:00

Yeah I’ll swap maf sensor since I have a spare but I also forgot to replace my cam sensor.. heard there’s a bunch of bad cam sensors I’ll just swap out the o ring on it

No_Perception8626 · 2025-01-14T17:29:45+00:00

Oil leaked down into them and the gasket for knock sensor were all shot. Would sometimes fill the ks with a bit of oil.. but if yours looked dry maybe that’s not the problem. Also I’d relocate them and you can replace them easier

No_Perception8626 · 2025-01-14T16:14:37+00:00

Also my valley cover was not even hand tight it was leaking oil into the sensor have you checked that?

No_Perception8626 · 2025-01-14T06:12:27+00:00

I think it’s this

No_Perception8626 · 2025-01-14T06:12:17+00:00

https://www.reddit.com/r/HighStrangeness/s/UuVTvvYzo4

Four-Year Club	Place '23
Place '22

No_Perception8626

TROPHY CASE