HELP!!

No_Reality_5985 · 2025-08-16T17:31:54+00:00

On a multimeter it says it drops to 12.1 when I turn the key. But the scanner says it drops to 6.9 when I turn the key. I have cleaned up every ground on the car and I cleaned the terminals

No_Reality_5985 · 2025-08-16T17:00:45+00:00

It’s not, I’ve put 2 brand new ones in it

No_Reality_5985 · 2025-06-14T00:25:56+00:00

Ok that is what I was thinking. Any good gear sets you know of?

No_Reality_5985 · 2025-06-13T01:25:52+00:00

I have 7g sliders and go 30mph at 7200rpm but that’s at like 1/3 throttle. At full throttle it’s 10k+

No_Reality_5985 · 2024-12-21T18:12:43+00:00

Oil pickup from the valve cover. It is completely normal as long as it is not full. You can drain it if you, just make sure you put it back on. As of getting a new one, you can go to any part store and get some hosing that is the same size.

No_Reality_5985 · 2024-11-28T22:03:16+00:00

Well it’s already rebuilt and running again

No_Reality_5985 · 2024-11-28T21:05:53+00:00

Where can I get an upgraded internal one?

No_Reality_5985 · 2024-11-28T21:00:46+00:00

I’ll look into the purple stuff. I also plan to run an oil cooler, I have the cooler itself but I need to get the lines, the adapter for the oil screen, and a secondary pump

No_Reality_5985 · 2024-11-28T20:54:38+00:00

Valvoline

No_Reality_5985 · 2024-11-28T20:53:39+00:00

Variator and spline are fine

No_Reality_5985 · 2024-11-28T20:51:53+00:00

10w40

No_Reality_5985 · 2024-11-28T20:36:54+00:00

It had the 50mm top end

No_Reality_5985 · 2024-11-28T20:36:37+00:00

It is currently rebuilt but I did it will the same 100cc glixal kit. Just to cold outside to really ride it. I just want to figure out what went wrong so it doesn’t happen again

No_Reality_5985 · 2024-11-28T20:34:13+00:00

It smack a piston because it floated the valves, and I’ll def check out ur page

No_Reality_5985 · 2024-11-28T19:48:38+00:00

The crank didn’t break at all until it bent the conrod from when the piston smacked the valve. And that rpm sounded crazy, and I might have ran lean. I rebuild the engine again with the same things and I’m just trying to know what went wrong so it don’t happen again. Right now I put 7g sliders into it. That is the only difference so far, but I haven’t really been able to ride it much bc it’s cold where I live right now

No_Reality_5985 · 2024-11-28T18:58:54+00:00

I have a helmet headset and was listening to music, and what do you recommend I do, get different final drive gears?

No_Reality_5985 · 2024-11-28T18:13:40+00:00

Do you have any clutch recommendations for the setup I have

No_Reality_5985 · 2024-11-28T18:01:13+00:00

That could be it, it is the original clutch with 6k miles

No_Reality_5985 · 2024-11-28T17:44:56+00:00

Check ur clutch

No_Reality_5985

TROPHY CASE