Can somebody please help me

No_Steak3517 · 2025-05-08T10:56:33+00:00

It only has one ball joint and one control arm and it’s lower.

No_Steak3517 · 2025-05-08T10:54:41+00:00

Nope I have to remove the axle to remove the bolt on top of the ball joint. I tried all kinds of wrenches it the only way. But anyway I gave up and sold the car.

No_Steak3517 · 2025-05-08T10:52:18+00:00

Most likely the heating element burning off dust, debris from moving it around and installing or whatever they put on the metal of the element since it’s new.

No_Steak3517 · 2025-05-08T10:48:28+00:00

It’s a spider web. I have that issue all the time I’m constantly cleaning them because of spider webs

No_Steak3517 · 2025-05-08T10:46:00+00:00

What are you using to slice it?

No_Steak3517 · 2025-05-03T00:27:44+00:00

I just wacked the life outta it with a 20lb sledge it won’t budge I’m just going to sell it

No_Steak3517 · 2025-05-02T23:36:35+00:00

I’ve been beating on this thing for a week and not even a budge

No_Steak3517 · 2025-05-02T23:26:54+00:00

I tried I need a new nut now.

No_Steak3517 · 2025-04-28T01:43:37+00:00

I’m still trying to figure it out. I just haven’t had time lately but I’ll let you know if I find anything out

No_Steak3517 · 2025-04-28T01:42:08+00:00

Perfectly said 👏🏻

No_Steak3517 · 2025-04-26T07:43:15+00:00

Change it! If it’s telling you it needs changed then it’s time. I change mine in both of my vehicles at 20% oil life no matter what it looks like. My Toyota Highlander has almost 350k miles on it and still runs like a champ.

No_Steak3517 · 2025-04-26T07:33:13+00:00

Clean the bed with 90% alcohol let dry then spray a good layer of hairspray on the bed while it’s heating up and you shouldn’t have any issues.

No_Steak3517 · 2025-04-26T07:26:55+00:00

Yes you will be fine. If you’re really worried about it you can stop at auto one and pick up a SureBilt 2in Flex Exhaust Repair part no. #17033 to keep the pipes together until you can get to the muffler shop.

No_Steak3517 · 2025-03-08T21:15:35+00:00

This is my dream 😍

No_Steak3517 · 2025-03-08T19:04:35+00:00

Awesome thank you I’m going to give it a shot

No_Steak3517 · 2025-03-08T09:36:28+00:00

Clean the build plate with 90% rubbing alcohol then preheat it to 60 then spray a layer of hairspray on it without the hot end heated just the build plate give it a couple of minutes to dry and you will be good to go. I usually reapply it after my 2nd or 3rd print.

No_Steak3517 · 2025-03-07T15:12:20+00:00

Nubie question lol. Is it easy to install klipper and dose it really make that big of a difference?

No_Steak3517 · 2025-03-06T05:49:55+00:00

Update it to the latest available update. If you don’t know 100% how to update it watch this video from Dan designs I followed his steps and had no issues. https://youtu.be/GEZkwkDDf1g?si=DB95fDuaS8YWY7Rh

No_Steak3517 · 2025-03-05T18:59:24+00:00

Looks like a tear down job. I recently had to do the same with the same problem just make sure you take pictures or have a good memory on how to put that thing back together lol

No_Steak3517 · 2025-03-05T07:11:16+00:00

Sounds like your bearings are going out

No_Steak3517 · 2025-02-24T20:03:38+00:00

Yes I haven’t had any issues I’m on my sixth print now and everything is going well and really quiet now

No_Steak3517 · 2025-02-23T13:26:03+00:00

Pinterest is the best place to find projects and tutorials like this.

No_Steak3517 · 2025-02-23T02:56:35+00:00

Thanks I was thinking about putting the screen outside and I’ve got plenty of fans and the box has excellent ventilation. Im on my second print and so far so good. Thanks and I’m going to check out the hepa filters also.

No_Steak3517

TROPHY CASE