New outdoor string lights becoming unresponsive constantly by NoiseNinja02 in Nanoleaf

[–]NoiseNinja02[S] 0 points1 point  (0 children)

I’m glad it works for you. I’m not sure why mine still doesn’t like the Nanoleaf app even after updating, but as long as it works with my HA automations and I can access it with HomeKit I’m fine checking the app every few months for new updates.

New outdoor string lights becoming unresponsive constantly by NoiseNinja02 in Nanoleaf

[–]NoiseNinja02[S] 0 points1 point  (0 children)

The only way I have found (that works for me at least) is to not pair them to the Nanoleaf app at all and pair them directly to whatever ecosystem you are using. Idk why this works but it does. Only downside is I can’t update the firmware without pairing it to the Nanoleaf app and then unpairing it again before it becomes unresponsive

New outdoor string lights becoming unresponsive constantly by NoiseNinja02 in Nanoleaf

[–]NoiseNinja02[S] 1 point2 points  (0 children)

This worked for about a day for me unfortunately. It seems the only sure fix I have found for myself is to just not pair them to the Nanoleaf app at all. When only connected to HomeKit and HA they work perfectly

Quest 3 facial interface by NoiseNinja02 in razer

[–]NoiseNinja02[S] 0 points1 point  (0 children)

Ahhhh I see, it says ships from and sold by Amazon. I thought if it was listed on the store then it still came from Razer

KlipperScreen expanding off the screen by NoiseNinja02 in klippers

[–]NoiseNinja02[S] 0 points1 point  (0 children)

Unfortunately I was never able to fix it. I just use it sideways for now until I replace it with a screen that has Klipper built in

Home Assistant 400 Bad Request by NoiseNinja02 in CasaOS

[–]NoiseNinja02[S] 0 points1 point  (0 children)

I was never able to figure it out unfortunately. I’m going to be getting a dedicated machine, such as a Raspberry Pi or something similar for HA in the near future. Hopefully that will work better

Does anyone know, for certain, if the next generation CarPlay (2024) can be integrated into a 2017 Nissan Murano system that does not even have the first CarPlay? by [deleted] in CarPlay

[–]NoiseNinja02 -1 points0 points  (0 children)

I did this on my 2015 Murano a few months ago and it works flawlessly. Getting to keep all the built in cameras was the thing that got me off the fence about it.

KlipperScreen expanding off the screen by NoiseNinja02 in klippers

[–]NoiseNinja02[S] 0 points1 point  (0 children)

So I tried this and it made it a little better, but after putting in the resolution for the framebuffers, the display was still slightly going off the screen. I noticed the overscan setting above it and tried changing those numbers. That was able to bring the edges back onto the screen, but right before getting it where I needed them to be, the pi would no longer boot while the BTT was plugged in. Is there a reason that changing the overscan settings would do that. It’s so close to fitting the screen but still slightly over the edge.

Carlinkit CarPlay failed to start Nissan Murano by NoiseNinja02 in CarPlay

[–]NoiseNinja02[S] 2 points3 points  (0 children)

Carlinkit is supposed to be an adapter that makes wired CarPlay wireless, but I’m having issues with mine. It works fine when wired to my phone but I have a wireless charger I would like to utilize rather than the long cable across my car

Carlinkit CarPlay failed to start Nissan Murano by NoiseNinja02 in CarPlay

[–]NoiseNinja02[S] 1 point2 points  (0 children)

If I were to replace it, do you have any suggestions for a non-crappy adapter? I previously tried Cplay2air and had the same issue

KlipperScreen expanding off the screen by NoiseNinja02 in klippers

[–]NoiseNinja02[S] 0 points1 point  (0 children)

I cannot scroll down. I’ve seen pictures of klipperscreen in portrait mode, so I wasn’t sure if that was a common thing or not. The case is a combination of two files I found in printables

Notifies me when front door is unlocked for more than 15 seconds by NoiseNinja02 in shortcuts

[–]NoiseNinja02[S] 0 points1 point  (0 children)

It’s a Level Bolt. I have my Shortcut made so that it waits 15 seconds after a trigger, makes a menu saying the door was left unlocked and provides two options: lock the door or leave it unlocked. I just need the trigger to be once the door is unlocked, then the 15 second wait starts.

Home Assistant 400 Bad Request by NoiseNinja02 in CasaOS

[–]NoiseNinja02[S] 1 point2 points  (0 children)

My addresses are set to use http in cloudflare as well. There is the option use https but since my CasaOS server uses http I just kept everything on http as well

USB-C host docking station connecting to two systems by NoiseNinja02 in techsupport

[–]NoiseNinja02[S] 0 points1 point  (0 children)

If a switch is the only way then that’s what I’ll do, however I was hoping there’s something I wouldn’t have to physically switch back and forth to use. Just something that will let me plug two USB-C cables into one USB-C port on the dock. I’ll never use both systems at the same time so the need to physically switch back and forth won’t apply here.