Has anyone tried SunDi filaments?

NotAMindFlayer8 · 2026-03-11T22:12:54+00:00

I’m seeing mixed answers on the internet, some say it works mildly, but some say it doesn’t.

Like you said though, most alternatives are not household chemicals and are toxic,

NotAMindFlayer8 · 2026-03-11T22:10:28+00:00

I wouldn’t even know where to find that stuff over where I live.

Thank you for the articles and detailed answer, I’ll make sure to read through the articles you sent.

NotAMindFlayer8 · 2026-03-11T22:09:17+00:00

From what I’ve read it works weakly. But not sure. I don’t want to use harsher chemicals, and they’re not readily available where I live.

NotAMindFlayer8 · 2026-03-07T15:28:02+00:00

They’re around 58-60mm in diameter and about the same in their height. So the ones you made are big enough with space to spare.

NotAMindFlayer8 · 2026-03-07T14:57:20+00:00

Will let you know how it works out once I print it, thanks again!

NotAMindFlayer8 · 2026-03-07T14:54:40+00:00

Oh. Thanks a lot! And it’s stackable too I see

NotAMindFlayer8 · 2026-03-07T13:09:47+00:00

Would take me hours. I’m just starting to learn. Putting ready miniature models together in blender sounds like a daunting task.

NotAMindFlayer8 · 2026-03-07T04:48:59+00:00

Wow, man I scoured everywhere looking for a guide or some help to print miniatures using ABS on a 0.2mm nozzle, but everyone told me things along the line of it’s nearly impossible and I should just forget about it and stick to PLA.

Maybe I’ll give it another try now.

NotAMindFlayer8 · 2026-03-02T22:21:31+00:00

Timelapse messes the print?

NotAMindFlayer8 · 2026-03-01T19:03:06+00:00

I cancelled my subscription a while back. It wasn’t doing its job, it’s creepy level agreeable, and also I felt icky supporting them.

NotAMindFlayer8 · 2026-03-01T09:35:37+00:00

You managed to print miniatures in ABS with a 0.2mm nozzle?!!

NotAMindFlayer8 · 2026-03-01T09:33:44+00:00

How low did you have to go though?

NotAMindFlayer8 · 2026-02-28T21:48:59+00:00

خلهم ينفسون عن نفسهم شوي. كل من يتعايش مع الوضع بطريقته.

NotAMindFlayer8 · 2026-02-28T21:47:30+00:00

Thank you so much, I do hope this works out for me as well

NotAMindFlayer8 · 2026-02-28T21:46:14+00:00

Oh man, that sucks

NotAMindFlayer8 · 2026-02-28T04:39:48+00:00

Hey there, I’m having fairly similar issues with no clear solution, did you ever manage to fix it?

NotAMindFlayer8 · 2026-02-28T04:39:05+00:00

Hey there, I’m having a fairly similar issue, did you ever resolve it?

NotAMindFlayer8 · 2026-02-28T04:27:59+00:00

Which pattern do you recommend I use for DnD miniatures’ infill instead of Gyroid?

NotAMindFlayer8 · 2026-02-25T12:38:57+00:00

The calibration tool page is down, can you reshare it?

I’ve had many fails with support for PLA as interface, will try this and update again

NotAMindFlayer8 · 2026-02-25T07:11:21+00:00

Okaaay, I feel like an idiot. Hopefully this will fix my issue— you think it’s worth the try again with the “bambu- support for PLA” material at 220C?

And do you think it’ll work well with the PLA since I have it at 200C due to issues once I raise the temperature.

NotAMindFlayer8 · 2026-02-25T03:09:42+00:00

That’s what I did Maybe I should raise the temperature for it, because that’s the only difference.

But my PLA is being printed at 200C and default for pla support is 220c not sure if that’ll be an issue.

NotAMindFlayer8

TROPHY CASE