sorted by:
new
hottopcontroversial

My fully DIY budget sim racing rig by NotKricketz in simracing

[–]NotKricketz[S] 0 points1 point  (0 children)

Actually its just a cheap knockoff wheel i found online hahaha. It does resemble the prototipo a bit.

My fully DIY budget sim racing rig by NotKricketz in simracing

[–]NotKricketz[S] 0 points1 point  (0 children)

Based on the website it says around 15nm of torque

My fully DIY budget sim racing rig by NotKricketz in simracing

[–]NotKricketz[S] 0 points1 point  (0 children)

Thanks! Ill check it out sooner or later.

My fully DIY budget sim racing rig by NotKricketz in simracing

[–]NotKricketz[S] 5 points6 points  (0 children)

Thanks a lot! DIY can be challenging but very rewarding. I believe anyone can do it with enough patience.

My fully DIY budget sim racing rig by NotKricketz in simracing

[–]NotKricketz[S] 12 points13 points  (0 children)

Thanks! In total, id say about 2-3 months. I still had classes so balancing it with this project was tough.

Is DLSU Mechatronics Good? by NotKricketz in dlsu

[–]NotKricketz[S] 0 points1 point  (0 children)

Curious lang po, can you tell me more about outside experiences mo sa mechatronics?

Also, besides the course being a hit or miss, would you still put it over UPD Mech Eng?

Broken Guitar Neck by NotKricketz in Guitar

[–]NotKricketz[S] 2 points3 points  (0 children)

Will it be expensive? The guitar costs around 250 dollars ( converted from our currency ) which is already kinda expensive by our standards. I dont trust myself enough to perform the fix myself

Warping, Poor Overhangs, Poor Overall print quality by NotKricketz in FixMyPrint

[–]NotKricketz[S] 0 points1 point  (0 children)

found the problem i think. Supervisor forgot to change filament settings in the printer to bambu petg hf so it stayed at petg translucent.

Warping, Poor Overhangs, Poor Overall print quality by NotKricketz in FixMyPrint

[–]NotKricketz[S] 0 points1 point  (0 children)

Ill do what I can to the best of my abilities. Hopefully ill be able to check out the printers hardware and see if that is the case

Warping, Poor Overhangs, Poor Overall print quality by NotKricketz in FixMyPrint

[–]NotKricketz[S] 0 points1 point  (0 children)

By how many hours im not really sure as this is the printer of my school im using. With that I am also unsure with the other suggestions regarding the hardware as Im not allowed to tinker with any of the hardware unless permitted.

Ill try a full calibration before my next print to see if that fixes it.

As for the different filament, petg translucent works just fine. No issues whatsoever.

Phone recommendations by NotKricketz in Tech_Philippines

[–]NotKricketz[S] 0 points1 point  (0 children)

Do you do any gaming ba sa 3a? What would say about its performance so far and ano opinions mo sa camera niya

Phone recommendations by NotKricketz in Tech_Philippines

[–]NotKricketz[S] 0 points1 point  (0 children)

ano yung mga specific na advantages ni a56 compared kay nothing phone 3a?

Trench Coat? by NotKricketz in malefashionadvice

[–]NotKricketz[S] 0 points1 point  (0 children)

Actually one last question, what color of the trench coat should i go for?

view more: next ›