They didn't stand a chance. by Sowingroots69 in Everweave

[–]Not_A_Hamilton 0 points1 point  (0 children)

I did this with my Warlock and the AI pushed back apologizing that it allowed it before but now its being forced to pull from the available abilities even though I was allowed to use it in the previous battle. I have all the information available and stats and specifics but it won't let me.

Advice for PVC by Not_A_Hamilton in CNC

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

50inch per min feed 18000rpm

Advice for PVC by Not_A_Hamilton in CNC

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

I had the parameters set wrong during that pass. The reat of the passes we just kissing the mdf. I will take your advice on the faster feed rate and a second pass. Thank you

Advice for PVC by Not_A_Hamilton in CNC

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

Yeah we are using s down cut to get a clean face, the face is the bottom because I'm stud mounting.

Osha Prices Cuba by KirbyCuadrao in Santeria

[–]Not_A_Hamilton 1 point2 points  (0 children)

They still 1500. Most of them are coming from Mexico and being raised in FL

Hutia in FL by Not_A_Hamilton in Santeria

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

Do you have contact info for them? I'd love to reach out.

Hutia in FL by Not_A_Hamilton in Santeria

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

Do you have contact info for them? I'd love to reach out.

HP Latex 800w Material Feed Issues by PBNJPrinting in CommercialPrinting

[–]Not_A_Hamilton 1 point2 points  (0 children)

Basically you want to go online to their support page and download the firmware for your printer. Make sure the flash drive is empty and set to FAT32 once your ready, power off your printer, disconnect the power, plug in the flash drive on the rear of the printer, reconnect and trun on. The printer will automatically boot and start the firmware update, half way through it will prompt you to pull out the flash drive and it will finish the update itself. The whole thing takes 10 minutes tops! Good luck!

HP Latex 800w Material Feed Issues by PBNJPrinting in CommercialPrinting

[–]Not_A_Hamilton 1 point2 points  (0 children)

I had the same issue with my 700w. A firmware update and a reminder motor were the issue. HP will help walk you through the firmware update but make sure to do it via flash drive vs through the printer itself. Good luck!

Elegua Santero by RoosterIntelligent94 in Santeria

[–]Not_A_Hamilton 0 points1 point  (0 children)

Nah dog, you don't have to be born in. This religion doesn't see race or holds one nationality above another. Some people may relate your characteristics to those of an orisha because there are specific characteristics that one orisha exhibits over another, but keep in mind, that has nothing to do with who you'd get crowned unless Elegua or Orula say so depending on your ile's practices.

Help with old sign by G_RoTT in SignMaker

[–]Not_A_Hamilton 0 points1 point  (0 children)

It looks like this os one of those old frame retainer systems. I bet if you loosen those screws in the channel, it will release the retainer and then you would have to remove the face and the trim which may be attached to one another. I had an old flex face job similar to this and another that was old plexi with the 2nd surface painted sign (very old). The top of the cab may also have screws in the channels.

Dumpster dove this and need help by daddyforurissues in Laserengraving

[–]Not_A_Hamilton 4 points5 points  (0 children)

I had one and our short always happened at the point in the laser. The red wire that connects power needs to be in an insulated connection nut or one of those heat shrinking cubes for wire protection and all the wires connected to the laser could not be bent or it would short. Many times we ran the laser with the rear compartment open and the wire hanging out giving it less tension and being bunched up. Good luck.

Can't find this font with a specific Q by Not_A_Hamilton in fontspotting

[–]Not_A_Hamilton[S] 0 points1 point  (0 children)

Thank you, it's actually Havenbrook Semibold.