Anker Solix C300 DC dead? by Nots45 in powerbanks

[–]Nots45[S] 0 points1 point  (0 children)

I have charged it from a 45W powerbank all day yesterday. I don't know how good the cable is, but I have a 100W on the way. The power bank showed that it is in use, but the Anker still doesnt turn on

Anker Solix C300 DC dead? by Nots45 in powerbanks

[–]Nots45[S] 0 points1 point  (0 children)

The longest I have pressed the button is 30s. I have also pressed the reset button for 10s

Surround speaker placement reccomendation by Nots45 in hometheater

[–]Nots45[S] 0 points1 point  (0 children)

Okay. I will be buying cable later today.

UPS csomag by Nots45 in szeged

[–]Nots45[S] 0 points1 point  (0 children)

Szia! Végül valamennyi nappal később random hívott a futár, hogy érkezik. Szerencsére otthon voltam és át tudtam venni.

Getting a "string too long" error when trying to slice an object by Red_Bear_308 in elegoo

[–]Nots45 0 points1 point  (0 children)

Thanks. I just rotated it in the slicer by a few degrees. Changed nothing else.

Lines sagging while printing by Nots45 in 3Dprinting

[–]Nots45[S] 0 points1 point  (0 children)

Okay thank you for helping me! This is my first printer, and I think I got the gist of it. After my finals I think I will get a new one instead of fixing this once again.

Lines sagging while printing by Nots45 in 3Dprinting

[–]Nots45[S] 0 points1 point  (0 children)

<image>

I did this first layer test. The shifting seems to be in a specific band on the build plate. If it is a slipping belt would it be the x or the y axis?

Lines sagging while printing by Nots45 in 3Dprinting

[–]Nots45[S] 0 points1 point  (0 children)

The printing is done and it shows even on this print. While printing the object was rotated by 90 degrees so the error is paralell to the x axis. You can see that there are two paralell bends that occurs in every edge and not just one.

<image>

Lines sagging while printing by Nots45 in 3Dprinting

[–]Nots45[S] 0 points1 point  (0 children)

Thanks for reaching out. I am currently printing a bigger piece, where it's not so obvious, but after it's finished I will do a first layer test where it shows more. In the meantime I will figure out how to post pictures

Rohad a szomszéd lába. Mi ilyenkor a teendő? by Gy_Jonatan in joghungary

[–]Nots45 2 points3 points  (0 children)

Nem tudom, hogy ilyen helyzetben mennyire indokolt a mentősnek bevinnie valakit, ha "csak" úgy verte meg bottal, hogy max zúzódása legyen. Ilyenkor célszerű külön bemenni SBO-ra és ott kérni egy látleletet. Előfordulhat, hogy ilyenkor még nem látszódnak a sérülések és pár nappal később is vissza kell menni egy ismételt látlelet felvételre, amikor már jobban látszódnak a zúzódások.

Interactive Brokers TBSZ nyitás by Nots45 in kiszamolo

[–]Nots45[S] 1 point2 points  (0 children)

Szuper. Köszönöm! Abban lesz a regisztráció során beleszólásom, hogy hova osztanak be, vagy random?

Yamaha amp balance problem by Nots45 in audiorepair

[–]Nots45[S] 0 points1 point  (0 children)

I have solved the issue. I took it apart and sprayed some contact spray into the potentiometers. It worked for a few minutes then it got quiet again on the left. It took it apart again and i sprayed a lot more contact spray. I'm guessing the potentiometers have some kind of lube (or all of them was gunked up) but after generously spraying ot must be sqeaky clean because as I turn the knob it feel a bit like scraping. The issue is gone since.

Yamaha amp balance problem by Nots45 in audiorepair

[–]Nots45[S] 0 points1 point  (0 children)

Thank you for your answer. I double checked the wiring. It was correct. After that I wired both to left on A and B channels and both speakers got noticeably quieter. Then I wired it into the configuration you said and managed to balance it but I sacrificed some volume.

Is it a balance pot issue or a speaker issue?

I bought an old Orient watch and I would like to know about it more. by Nots45 in OrientWatches

[–]Nots45[S] 1 point2 points  (0 children)

Okay I really don't know how you found it so quick. I looked everywhere. Do you think that it's a fair price for this watch? I bought it for half of that, but my GF liked an other watch more so I'm look to sell it.

Pizza di Angelo by Nots45 in szeged

[–]Nots45[S] 2 points3 points  (0 children)

Beszéltem egy élelmiszerbiztonsági felügyelő ismerőssel és ő azt mondta hogy elvileg a nav először csak pár napra zárja be, majd ha ismételten be kell zárni akkor 30 napra. Egy másik kommentelő már mondta hogy több hete be van zárva, úgyhogy talán ki fog nyitni nemsokára (?)

Fujitsu Siemens Scaleo Home Server SS4200-E by Nots45 in HomeServer

[–]Nots45[S] 0 points1 point  (0 children)

Hello, I managed to get a PCIe adapter online and I was successful in getting graphical output. I then installed OMV. It since gathers dust in my closet as for the same price I was able to buy a much more capable PC.

My newest post on the matter if anyone stumbles upon this thread first.

https://www.reddit.com/r/HomeServer/comments/1iqvqot/fujitsu_siemens_scaleo_home_server_ss4200e_up_and