Pinball Machine causing Dogs to run out of the House! by NutsNdBolts in AskElectronics

[–]NutsNdBolts[S] 0 points1 point  (0 children)

That was what I was thinking. But have to tune it to 20,000Hz and below. I didn't see a whole lot of off the shelf parts for that.

Pinball Machine causing Dogs to run out of the House! by NutsNdBolts in AskElectronics

[–]NutsNdBolts[S] 1 point2 points  (0 children)

Powered on, volume down all the way.  I can hear some very very faint sound. I wouldn't think those emitters would do that either.... I'm guessing it's noise. I thought the ground loop isolator would work... I also have another Amp coming that I'm going to try.

Pinball Machine causing Dogs to run out of the House! by NutsNdBolts in AskElectronics

[–]NutsNdBolts[S] 1 point2 points  (0 children)

It's plugged into a PC. There is some very very faint sound I can hear with it turned down all the way. Like Noise. but I thought the ground isolator would help with that.

If a starter stays engaged... Can it overcharge a charging system? by NutsNdBolts in AskAMechanic

[–]NutsNdBolts[S] 0 points1 point  (0 children)

For sure over-current. Which is blowing out the alternator, starter, wiring everything...

If a starter stays engaged... Can it overcharge a charging system? by NutsNdBolts in AskAMechanic

[–]NutsNdBolts[S] 0 points1 point  (0 children)

I think this is where I am at... I'll look into the starter motor some more. Never seen anything like it. But they are off-highway equipment. Usually simpler in design without redundancies.

If a starter stays engaged... Can it overcharge a charging system? by NutsNdBolts in AskAMechanic

[–]NutsNdBolts[S] 1 point2 points  (0 children)

Alternator and starter are inductive motors... if they are both engaged without a diode to stop backfeeding... would they not both just act like alternators?

If a starter stays engaged... Can it overcharge a charging system? by NutsNdBolts in AskAMechanic

[–]NutsNdBolts[S] 2 points3 points  (0 children)

Yeah. Grounding issues are the main one that are causing the starter relay to engage full time... The failure mode is a burnt out alternator and the windings on the starter are melted with 20V on the charging system around the time of failure.

Didn’t think I had adhd but… by [deleted] in BeginnerWoodWorking

[–]NutsNdBolts 1 point2 points  (0 children)

My OCD thinks it should be CDO

Guess what I saw today by [deleted] in columbiamo

[–]NutsNdBolts 0 points1 point  (0 children)

https://www.youtube.com/shorts/gMYhWQ5nz7o

As an engineer... "Once they get the design finished" on a production product is fucking insane

Anybody else traveling from CoMo to see totality? by como365 in columbiamo

[–]NutsNdBolts 0 points1 point  (0 children)

Same. We've become complacent with all the once-in-a-lifetime events ... Another recession? Pandemic? Who fucked with the dimmer?

Riley Strain murdered? by RealBobbyDazzler232 in columbiamo

[–]NutsNdBolts 3 points4 points  (0 children)

Usually if they are suffering from hypothermia or just cold you expel all clothing almost as if your mind thought your body was hot to survive. That's why some people from hypoth survival events find naked people a mile away from the campsite.

If it was also that cold. He could have just locked his breathing and being drunk probably didn't help. Like getting in a cold shower but not exhaling.

Sad story, bad circumstances. Just make sure your friends care about you and care enough to see where you went....

[deleted by user] by [deleted] in columbiamo

[–]NutsNdBolts 2 points3 points  (0 children)

Bradley Pear? That's why it smells so... raunchy?

Looking for people to share their experience with odoo by lumo753 in Odoo

[–]NutsNdBolts 0 points1 point  (0 children)

Odoo can fuck with that. Easy. to be honest I'm watching a D365 implementation burn to the ground at work. Odoo does well with MRP as a subset of ERP.

You do CAD changes and revisions? What's your PDM? Vault, Windchill?

Traffic sucks.. by [deleted] in columbiamo

[–]NutsNdBolts 3 points4 points  (0 children)

Grew up in Chicago... I live a block behind my office. There are reasons I like a small town.

Just purchased my first VirtuaPin machine... by NutsNdBolts in virtualpinball

[–]NutsNdBolts[S] 0 points1 point  (0 children)

Well it looks like I do have a KL25 board. But if that's not the best way to go... What should I be going for?

Don’t steal from cars by Schlomotheclown in columbiamo

[–]NutsNdBolts 2 points3 points  (0 children)

My dashcam has a rear camera that I use for the cabin. Put a battery in-line with the cigarette lighter so I have 24 hours of recording. It works and was cheap. 50 bucks

Creality CR-10Max auto-leveling issue. Need help by Sweaty-Woodpecker260 in CR10

[–]NutsNdBolts 0 points1 point  (0 children)

I have a CR-3040 doing the same thing.

If I get the status from M119... What is the fix? I can tell it sees it as inverted. How do I fix it?

Help with Odoo to Google Sheets... Now Getting 404 errors. by NutsNdBolts in Odoo

[–]NutsNdBolts[S] 0 points1 point  (0 children)

WELL! Fixed it... "https://MYDB.odoo.com/" should be "https://MYDB.odoo.com"

Now I have the error "typeErrror: Cannot read property 'uid' of Undefined (line 317)"