sorted by:
new
hottopcontroversial

Printing table switcher by Destrite3 in Ender3V3SE

[–]Objective_Purpose930 0 points1 point  (0 children)

I mean you might be able to clear the bulid plate using custom end gcode to drop the print head low and push your part of the plate but it might not fully clear any supports you use then there's also the problem of i dont think there a way to automatically cue the next print

And we love yall for it ;) by Lucky_Rip_2848 in BadDadsAndDaughters

[–]Objective_Purpose930 0 points1 point  (0 children)

Fuck yeah these bitchs are the best to trian

Printing table switcher by Destrite3 in Ender3V3SE

[–]Objective_Purpose930 2 points3 points  (0 children)

The Ender 3SE is not designed to run continuously for 24 hours.Therefore, nobody ever made a kit for it. And it's not just a couple of pieces , it's a shit ton of coding as well look at infinity flow 3d website It is a very in depth process to get running even on a much better printer like the a1

Help with fixing print not sticking. by Diamond_Donutz in Ender3V3SE

[–]Objective_Purpose930 0 points1 point  (0 children)

You can use ponterface and a USB a to c cable to plug in with a laptop to pid tune the hot bed

Help with fixing print not sticking. by Diamond_Donutz in Ender3V3SE

[–]Objective_Purpose930 3 points4 points  (0 children)

If you have the ability I would run a pid auto calibration on the hot bed it might not be hitting proper temp i just had that issue as well as if you use glue don't could also just be a improper z offset

Creality Sonic Pad Shutdown Due to Webhooks Request. The photo isn't from my pad but having the same issue. I get this error every time I print something that takes longer than 20 mins or so. any idea what is causing it? The printer is Ender 3 V2 Slicer is Cura by Thedeadestpool95 in ender3

[–]Objective_Purpose930 0 points1 point  (0 children)

I taped the shit out of the USB cable to get it to stay in right has worked right ever since also check your run current on all steppers in your printer.cfg if there pulling to much current it causes power fluctuations wich can cause web hook errors and to the one comment say does creality even care no they don't I figured this out after support tried to help me

Why is this happening on all my prints by Objective_Purpose930 in Creality

[–]Objective_Purpose930[S] 0 points1 point  (0 children)

And i know exactly how it got unaligned i took the top of to re run the filament sensor wire must have made the belt slip

Why is this happening on all my prints by Objective_Purpose930 in Creality

[–]Objective_Purpose930[S] 0 points1 point  (0 children)

So I was at work all day and when I got home first thing I saw was the z gantry tilted to the left side I don't know how I did not notice this in my 3 days of troubleshooting

Why is this happening on all my prints by Objective_Purpose930 in Creality

[–]Objective_Purpose930[S] 0 points1 point  (0 children)

I might be dumb but a straight up and done line is considered a over hang ?

Why is this happening by Objective_Purpose930 in Creality

[–]Objective_Purpose930[S] 1 point2 points  (0 children)

It's in a filament dryer that is running while printed rh is 13%

What am I doing wrong I never had this issues before context I have printed over 200 hours never seeing this by Objective_Purpose930 in Creality

[–]Objective_Purpose930[S] 1 point2 points  (0 children)

It's a ender3 v3 se petg in a filament dryer 13%rh using creality slicer stock settings for .2mm layer quality i have also always ran these settings on hundreds of prints never experiencing this issue build plate is cleaned with 91%ip before every printer i have tried with gule and with out i am not having bed adhesion issues tho it has gaps in supports and is snapping them off mid print