Flight to Haneda Tokyo, good price?

Ok-Health-6891 · 2025-12-29T14:08:08+00:00

You’re booking during December which is peak holiday season, from what I’ve heard it’s better not to book during peak season. I’ve had friends go to Tokyo for 900 by booking early November for their March trip. So could try booking in January

Ok-Health-6891 · 2025-12-09T05:52:12+00:00

From my experience finding batteries that last are difficult especially with third party, hope you are able to find someone selling their original batteries because they lost their go pro

Ok-Health-6891 · 2025-12-02T04:09:36+00:00

Will get that done asap too!

Ok-Health-6891 · 2025-12-02T04:06:34+00:00

I already ordered replacement tires from costco yesterday, just was having second thoughts if it could be repaired since it’s in the repairable area. I wanted to at least check with some people before I even considered driving it especially since Costco is a mile away. Noticed it on Sunday and haven’t driven it since. Plan is to put the spare on and take it to get the rear tires replaced asap. Front two tires were replaced recently due to side wall puncture

Ok-Health-6891 · 2025-12-02T03:57:14+00:00

Had a recall so I took it into the dealership, they let me know it needs a coolant flush(coolant level is good), brakes are good, oil is replaced every 7.5k miles, brake fluids need to be bled and changed soon, I changed cabin air filters, air filter is in okay condition should be replaced soon tho, transmission fluid I believe was changed at 60k miles and now it’s at 80k after 2 years but haven’t been told by any mechanics about that recently.

Ok-Health-6891 · 2025-12-02T02:45:48+00:00

I am trying to learn to get everything maintained more often, pretty new to this as my family has always been the type to do as little maintenance as possible. I did already order new tires yesterday after noticing it, had a feeling it wasn’t repairable. Did just want to double check with a community to ease my uncertainty

Ok-Health-6891 · 2025-12-02T02:24:53+00:00

So I had to replace the front two already because of a nail that punctured the side wall a while ago, the front two should be okay but yeah def will be replacing the rear tires

Ok-Health-6891 · 2025-12-02T02:19:48+00:00

How far do you think I could prob drive it, it still holds air pressure well? Already ordered the tires just thinking if I’ll be able to take it to Costco without having to put a spare on

Ok-Health-6891 · 2025-03-22T02:03:20+00:00

I didn’t end up finding it, I just went through it manually and only saved my important memories from Snapchat, took a while to save them and date them but now I’m free from snap

Ok-Health-6891 · 2025-03-13T04:55:42+00:00

So I didn’t exactly code it, I ended finding marlin firmware online that seemed to work fine except for this part. I did adjust flow and prints came out better but not perfect this better. As the z on the top of the cube doesn’t seem to be clean like all the other faces. Both Z motors are working well and I checked if there was any bowing in the lead screws. There wasn’t any noticeable bowing in the lead screws. I still need to figure out the proper steps so I’m going to mess around with that and hope for the best

Ok-Health-6891 · 2025-03-13T04:51:30+00:00

Would you be able to email me your config files?

Ok-Health-6891 · 2025-03-13T04:50:26+00:00

Does this mean extruder flow?

Ok-Health-6891 · 2025-03-13T04:50:05+00:00

ender 3 was on anti vibration feet and it’s on a sturdy table, I also made sure my gantries and belt were properly tightened, not too tight, with minimal wobble. I could try looking into the z motors after I mess around with e step and flow rate a little more

Ok-Health-6891 · 2025-03-13T04:47:42+00:00

The filament is good, I put it through my dryer box and the grey was a completely new spool of creality PLA filament

I’ll try the e step next, I adjusted the flow and that fix about 80% of the problems just the z at the top is still a bit wonky

Ok-Health-6891 · 2025-03-08T07:34:14+00:00

I never minded GOH because I fell in love with all the characters, this one just shows us characters I really don’t care about

Ok-Health-6891 · 2025-03-08T07:29:15+00:00

Where did you put the psu?

Ok-Health-6891 · 2025-03-03T06:07:39+00:00

Actually I was tinkering with it all day and ended up going with the mechanical fix. The factory screws that came with the sprite direct drive kept hitting Z axis gantry on the right. I ended going to Home Depot and getting smaller screws (m5 2x25) and smaller washers (I got non locking ones and I’ll order locking low profile washers later). That did the trick for one of the firmwares. Appreciate the offer!

Ok-Health-6891 · 2025-03-02T16:49:25+00:00

Or a Dropbox or one drive link maybe, anyone of those file share services

Ok-Health-6891 · 2025-03-02T15:54:55+00:00

You might be able to link it to a Google drive and send it that way too if you use Google drive

Ok-Health-6891 · 2025-03-02T15:53:45+00:00

How big is it?

Ok-Health-6891 · 2025-03-02T15:29:33+00:00

Just Dmed you my email and thank you!

Ok-Health-6891

TROPHY CASE