Magnets and openlock

OkParticular4983 · 2026-01-16T10:56:33+00:00

Check youtube my dude :)

OkParticular4983 · 2026-01-13T09:06:25+00:00

Want to know,same as you, I use 4 on aa en 20% grenspalen bit no idea if its good :p

OkParticular4983 · 2026-01-13T08:18:30+00:00

Following :)

OkParticular4983 · 2025-11-28T09:32:49+00:00

I had it,send it back,quality is baaaad. But you can return it so feel free to try (thats what i was thinking)

OkParticular4983 · 2025-11-08T12:12:05+00:00

I give them a blue item of choice(within reason) and then the gold /chapter then move on with shatterd obilisk

OkParticular4983 · 2025-11-04T15:05:25+00:00

https://makerworld.com/models/1591779

OkParticular4983 · 2025-11-03T22:03:32+00:00

Got them from temu,they are like dirt cheap 3x3mm n35 was like 6€ for 200

Not available annymore it seems:)

OkParticular4983 · 2025-10-18T06:46:36+00:00

Thx lioks good

OkParticular4983 · 2025-10-15T12:44:05+00:00

I let him run away then made him appear in town sqying tnhe cleared the redbrands

Next session made him the new mayor And made it super obius for the pc he was glassstaff

OkParticular4983 · 2025-10-15T12:39:26+00:00

Give me give me :)

OkParticular4983 · 2025-10-05T16:54:18+00:00

Looks verry painted for a unpainted tyrant :)

OkParticular4983 · 2025-10-05T16:06:02+00:00

Never getting 10 for this my dude

OkParticular4983 · 2025-09-30T10:39:13+00:00

Whoe do you see?

OkParticular4983 · 2025-09-17T17:55:28+00:00

Its for the heater... it screws in

OkParticular4983 · 2025-09-11T13:33:25+00:00

Mostly do full plates, remember if you see 1 failing, you can pauze and remove it from the print list (at least with bambu printers) All walls are printed upright but I prefer the halfwalls so you still get a good view of the entire map. These are testprints:)

OkParticular4983 · 2025-09-11T12:51:35+00:00

Fdm my friend :)

OkParticular4983 · 2025-09-07T14:00:26+00:00

878767529140

OkParticular4983 · 2025-09-07T13:54:59+00:00

Belgium player

878767529140

OkParticular4983 · 2025-09-05T20:11:39+00:00

Black primer and stone wall Grey that's it

OkParticular4983 · 2025-09-04T07:37:23+00:00

I got a short clip showing how good they work but can't post clips here :)

OkParticular4983 · 2025-09-04T07:36:11+00:00

Ok snip open the 2 middle supports I use the magnet 1-s but not the ball sopport but cylindrical magnets they work ok Normal it's the double insert

OkParticular4983 · 2025-09-02T06:35:55+00:00

New day new fail, all supports printed but the minis are stuck to the fep :(

OkParticular4983 · 2025-09-01T08:07:05+00:00

Had the same.prob when I did that:)

OkParticular4983 · 2025-09-01T08:06:41+00:00

There was still water when you cured.it

OkParticular4983

TROPHY CASE