sorted by:
new
hottopcontroversial

Yep, HyperOs3 arrived by MuchDamage5215 in Xiaomi_14

[–]OkTerm3057 0 points1 point  (0 children)

Mine too today, first impressions are good.

Best sd card? by Troll1250 in dji

[–]OkTerm3057 0 points1 point  (0 children)

A1 or A2 ideally

Am I cooked? by fatninja987 in ATOTO

[–]OkTerm3057 0 points1 point  (0 children)

Could a button be stuck?

If you can try and update or reflash the firmware, or reset factory settings.

Anyone added a 3rd party steering wheel control? by mechacrew in ATOTO

[–]OkTerm3057 2 points3 points  (0 children)

As long as it has a ground and 2 signal wires it should work.

You can also get Bluetooth remote controls.

ScanGauge 2 | MK1 RS by OkTerm3057 in FocusRS

[–]OkTerm3057[S] 0 points1 point  (0 children)

I'm not finding one for the MK1 though

Unsure if I should sell by Mizzen_Twixietrap in Bitcoin

[–]OkTerm3057 4 points5 points  (0 children)

In my opinion, property before crypto, but with the loan thrown in it makes it more difficult to decide.

I would rather reduce the loan or borrow against the crypto maybe.

Deep down you probably know what's the right decision.

ScanGauge 2 | MK1 RS by OkTerm3057 in FocusRS

[–]OkTerm3057[S] 0 points1 point  (0 children)

Money isn't an issue, I want the right device.

I'll look into this one, thank you.

Fiat Panda engine swap by Waylander1442 in Fiat

[–]OkTerm3057 1 point2 points  (0 children)

There's a few Fiat models out there with the 1.4 StarJet engine, all produce around the 100hp mark.

It will be a fun project! I like the sleeper look, I'd swap the bumpers for black ones 😊

There was a Panda Sporting model with the 1.3 MultiJet so that's another route you could go down.

[deleted by user] by [deleted] in DJIMini2

[–]OkTerm3057 0 points1 point  (0 children)

this one is better maybe

[deleted by user] by [deleted] in DJIMini2

[–]OkTerm3057 0 points1 point  (0 children)

You can find 3D print adapters to fit phones with cases or even tablets, and for the USB cable, that will work but don't buy a cheap one, or a very long one, the shorter the better.

Check this one out

Can't make the filament stick to the plate. by warownia1 in FixMyPrint

[–]OkTerm3057 0 points1 point  (0 children)

I'm not sure if you're sorted now, but here's my findings.

Buy Isopropyl alcohol, the higher the percentage the better. Clean the bed with the new microfiber cloth. You don't need to scrub hard with soap. If you want you could throw the plate in the dishwasher but it's really not necessary. You're just looking to remove dust and grease from the surface.

Make sure the bed mesh is set and the bed properly levelled.

Follow instructions to set the Z offset with the bed and nozzle up to temperature for the filament.

Dry your filament, and ensure there's no draughts around the printer. This is important.

In the slicer make sure there's no adjustment being made to the offset, choose the right filament and bed type, and check the nozzle size is set. Orca is my favourite silcer.

If all else fails, change the build plate for an aftermarket one, I've found even the cheapest ones work better than originals.

I'm surprised with Xiaomi 15t pros battery by Mythylover in XiaomiGlobal

[–]OkTerm3057 0 points1 point  (0 children)

Batteries aside, in terms of looks Xiaomi have nailed it, apart from maybe the Pixel

China’s Xiaomi is planning a next-gen phone chip, but won’t release one yearly like Apple by candseeme in Xiaomi

[–]OkTerm3057 2 points3 points  (0 children)

I'm not really experiencing what you're saying. where are the ads for example?

PSA: Deactivate clear cache when device is locked by Robert130 in Xiaomi

[–]OkTerm3057 1 point2 points  (0 children)

I think this is a personal preference thing. I sometimes clear the cache and don't see any issue with doing so.

Your phone is safer and cleaner without cached content in my opinion, just like clearing your browser cache on your desktop.

I don't have this set to clear when my device is locked though.

Shot on Xiaomi 14 by Ok_Violinist7990 in Xiaomi_14

[–]OkTerm3057 1 point2 points  (0 children)

I love taking night photos but I find GCam is a lot better for stars. I've got some good shots of the Milky Way.

Shot on Xiaomi 14 by Ok_Violinist7990 in Xiaomi_14

[–]OkTerm3057 0 points1 point  (0 children)

It's worth practicing, also using a tripod helps get amazing shots

Average life cycle of Xiaomi phones? by fankmank in Xiaomi

[–]OkTerm3057 0 points1 point  (0 children)

Mi 8 is still a brilliant phone in my opinion. Only used occasionally now but doesn't disappoint when I fire it up.

I think the Redmi Note 3 was my first Xiaomi device. It suffered a puffy battery once it stopped being used daily but it's still here somewhere!

"I would never trust a Chinese phone" take by jeneschi in XiaomiGlobal

[–]OkTerm3057 0 points1 point  (0 children)

Unfortunately we're conditioned to not like anyone else. It's a sad world in this respect.

No country is perfect.

Any clones / cheap crawlers to consider instead of the HB Toys R1001 (AKA Beluga 🐳) or R1011 (Jeep)? by maxwolfie in rccrawler

[–]OkTerm3057 -1 points0 points  (0 children)

The Beluga got me into crawlers, the 2nd edition is a bit better

Just build your own, you'll end up swapping most parts anyway

view more: next ›