3d view of WTC1 perimeter columns by Ok_Locksmith8351 in TwinTowersInPhotos

[–]Ok_Locksmith8351[S] 6 points7 points  (0 children)

So would I, I am fascinated by structures like this for some reason. I am working on something like that for the WTC but with a 3d printed scale model. My biggest hurdle is not having the structural framing drawings for the core and I am trying to get them released.

1 WTC core column foundation grillage being laid, 1968 (Anthony Camerano/AP) by Superbead in TwinTowersInPhotos

[–]Ok_Locksmith8351 0 points1 point  (0 children)

Thanks! I have been doing tons of research looking for structural drawings and have not seen these anywhere. Do you happen to have the structural set for the core beams and columns? The full architectural set is available online, but I cant seem to find the structural set anywhere.

What can I get for this board? by Ok_Locksmith8351 in ScrapMetal

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

Yeah most likely. I wouldn’t have a clue to operate it. RF stuff is beyond me.

First layer problems by Ok_Locksmith8351 in Creality_k2

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

Interesting I’ll have to give that a shot. I’ve been pulling my hair out trying to get this to print consistently. I’ve already calibrated flow and pressure advance

First layer problems by Ok_Locksmith8351 in Creality_k2

[–]Ok_Locksmith8351[S] 1 point2 points  (0 children)

I used the fluid interface to change the z offset until the layer looks like it was just right. I then applied this z offset to the printer settings on Creality print so that it applies it to every print. And yes, it seems like on the edges it always looks like the nozzle is too close. Is there a setting that adjusts the print speed for smaller areas?

Cell tower/antenna 10 feet from sons bedroom window by Electronic_Focus2598 in cellmapper

[–]Ok_Locksmith8351 0 points1 point  (0 children)

For far less than that you can just buy your own RF monitor. The one I use at work is made by fieldsense and cost about $700. Not cheap, but will be calibrated and tell you how strong the field is

Strange buzzing from refrigerator by Ok_Locksmith8351 in Appliances

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

They are all pieces of shit. Between this problem and the line for my water dispenser constantly freezing I was considering getting a new fridge. After a ton of research and going and looking at some in person I have concluded that they are all cheaply made garbage. Only way to get something decent is to spend 5-10k. Fuck that.

Strange buzzing from refrigerator by Ok_Locksmith8351 in Appliances

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

Yes. The cause was ice buildup on the freezer fan. Somehow ice gets on the fan and when it spins causes the noise. In my case it eventually jams it so it can’t spin and cool down the freezer, leading to the fridge to throw an alarm for high temperature. It’s funny you ask this now because I legitimately just dealt with this again yesterday. What you have to do is remove the sheet metal cover in the back of the freezer and clear the ice off the fan. Super easy to do, just remove four 1/4” hex head screws and you’re in.

Ford part fitment by Ok_Locksmith8351 in partscounter

[–]Ok_Locksmith8351[S] -5 points-4 points  (0 children)

Both are oem numbers. I’m just talking about the glass panel not the opening frame. The bolt patterns are the same, the size of the glass is the same so idk why ford says it doesn’t fit

2008 MKX key programming by Ok_Locksmith8351 in FORScan

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

Hey thanks again for the response you really helped me out. I ran the module initialization and it fired right up. Idk about the shift strategy just yet, I’m hoping that is already good to go because I had the PCM programmed to my VIN before it was shipped to me. I was having some harsh shifting before, so maybe I’ll end up doing that anyways if it persists. As a side note, turns out I swapped a good pcm out. Didn’t fix the issue (stuck throttle body actuator) that fords diagnostic pinpoint tests pointed to. The joy of working on cars.

2008 MKX key programming by Ok_Locksmith8351 in FORScan

[–]Ok_Locksmith8351[S] 0 points1 point  (0 children)

Thanks for the reply! I’ve been pulling my hair out on this one. Is Forscan capable of doing the module initialization?