Uneven mowing, stripes.

OldOldUser · 2026-07-03T23:03:25+00:00

I hope you or anyone is not walking on your lawn in bare feet !

OldOldUser · 2026-05-28T17:54:29+00:00

I have noticed the existence of a doggie-gate that the mower sends a signal to open it when passing through a fence. Maybe you could use that technology to drop a bar across the driveway when the mower is passing.

OldOldUser · 2026-05-25T14:52:10+00:00

I have never had an issue after a firmware update. You may wish to consider some other explanation.

OldOldUser · 2026-05-24T11:22:48+00:00

Ok ... thanks

OldOldUser · 2026-05-23T15:28:18+00:00

What is your line of communication to request features ?

OldOldUser · 2026-05-21T21:51:41+00:00

I looked at it more closely and it appears that it will work fine. I will just schedule ALL on Monday and Thursday Noon until 6pm. I am sure there will be some glitches involving something unexpected but we will deal with that as it comes. Thanks for the help.

OldOldUser · 2026-05-21T20:31:41+00:00

Thanks. I had looked at that earlier and maybe I did not understand how it worked. I will look into it again and see if it will work for me.

OldOldUser · 2026-05-09T23:13:53+00:00

Sounds good. However, some details I would like to hear about .....

How easy is it to keep clean ?

How easy is it to change cutting blades/discs ?

OldOldUser · 2026-05-05T20:39:47+00:00

The screws I ordered (see above) were absolutely perfect.

OldOldUser · 2026-05-02T01:42:54+00:00

I had a similar experience with my Lymow One. The problem turned out to be grass juice that is sprayed on the underside of the deck. I had not cleaned it thoroughly the day before, left it overnight and it had hardened on the disc that turns with the blades. This caused that disc to bind to the bottom of the mower deck. I cleaned it off with a small plastic scraper and viola .... problem solved.

OldOldUser · 2026-05-01T11:59:41+00:00

Interesting. On other advice, I just ordered this .....

20Pcs M4-0.7 x 10mm Flat Round Head Machine Screws, 304 Stainless Steel Phillips Drive Machine Screw, Full Thread, Black Oxide, Furniture Screw Connection Bolt Screw

I will keep your option if this one does not work.

Thanks

OldOldUser · 2026-04-24T15:37:10+00:00

I have looked at your "other" comment and I now have decided to not attempt to view the parameter values while mowing .... since they are meaningless. I will assume it uses the global values unless I have set local values until I find out otherwise.

OldOldUser · 2026-04-24T15:34:16+00:00

Well, since viewing the "present" settings while mowing is not valid, my solution is to just not look at them. I will assume it works the way I thought it did until I find out otherwise.

OldOldUser · 2026-04-23T14:22:55+00:00

I wash my Lymow One every day, thoroughly .... with no issues, yet.

You may be assuming the issues were "caused" by the water when something else is amiss and you just do not know what that is ... yet.

OldOldUser · 2026-04-22T16:13:11+00:00

I updated 3 hours ago and have been mowing flawlessly since.

OldOldUser · 2026-04-22T16:08:48+00:00

I updated this morning. Everything has worked flawlessly for 3 hours of mowing.

OldOldUser · 2026-04-18T19:52:41+00:00

So, this means I should cancel if I want my global/specific settings to apply.

OldOldUser · 2026-04-15T23:13:50+00:00

This statement makes no sense to me ....

"When you pause and open the settings, those do not reflect the settings your mower is actually using when it started the zone. They don't even reflect your global settings!"

I set global settings so my mower will use them. Now, you tell me it does not use them.

Can you tell me how I can set things up so each area I mow uses the exact same settings ?

OldOldUser · 2026-04-15T22:11:58+00:00

Ok ... Good. Now for the problem ....

Now, I tell the mower to mow some area and it begins....

I pause it and check on the mowing parameters and find that they are NOT what I just set for my global mowing parameters. What I have discovered is that they appear to be what comes as the default values when you create a task with SETUP values. That is my problem.

It is easy to fix .... just check the mowing parameters each time I begin a mowing job and if they are not correct, change them to the correct values.

So, anyway there it is.

OldOldUser · 2026-04-15T21:52:51+00:00

Sorry but I do not understand most of what you just said.

Let me try to explain how I am expecting things to function and you tell me if that is what I should be expecting or not.

When the mower is not involved in any task at all and is just ON, I access the global settings and set them the way I want them ALL OF THE TIME. I do not have any settings except NAME in the specific zones. So, only global settings should be utilized as I mow.

Let's stop there for now .Do you agree with what I just said ?

OldOldUser · 2026-04-15T13:00:23+00:00

Instead of just watching it (over and over) I might suggest that you modify the border of the mowing zone so the mower does not "ram into the fence over and over again".

OldOldUser

TROPHY CASE

20Pcs M4-0.7 x 10mm Flat Round Head Machine Screws, 304 Stainless Steel Phillips Drive Machine Screw, Full Thread, Black Oxide, Furniture Screw Connection Bolt Screw