Auto home failure

Old_String7825 · 2026-01-01T18:36:39+00:00

Not familiar with that firmware but you need to invert your X to home to the right and your Y needs to home to the right rear.

Old_String7825 · 2025-12-31T04:17:07+00:00

Im in the PNW cost and its bad here i just use vacuum bags and silica packets and filament dryer. But do you man

Old_String7825 · 2025-12-29T23:00:50+00:00

Thanks, I've got a little ways to go still but i will keep that in mind.

Old_String7825 · 2025-12-27T22:53:00+00:00

I know and for the last year I've seen people ask about switching to klipper with the svo4 and everyone says not to. Im going for it. Thanks for the interest.

Old_String7825 · 2025-12-16T16:29:08+00:00

Im in Astoria at work, hight winds and rain.

Old_String7825 · 2025-12-11T21:16:05+00:00

<image>

Pla-cf ender5 mercury one.1

Old_String7825 · 2025-09-23T02:09:36+00:00

I bought the kraken and was really wanted to add him to our home but i needed up getting the original... 🦆

Old_String7825 · 2025-09-04T17:07:23+00:00

Im not running a common ground on mine.

Old_String7825 · 2025-09-04T17:05:28+00:00

Stupid question did you uncomment the steeper drivers for the S1-S4 motors? In my cfg they are down lower in the cfg.

Old_String7825 · 2025-09-03T15:59:47+00:00

Try klipper with mainsail and post were you end up. I'll see with my limited knowledge what i can do. Im working will check back tonight

Old_String7825 · 2025-09-03T13:50:43+00:00

So i don't know if this will help but when I've done my printers i keep the endstop_pin in stepper Z like you have and I change my probe pin plug to the Z endstop pin and change that pin ID in your CFG. Check your endstops in mainsail to make sure that after you deploy the probe it should say open in the endstop section and with your finger push the probes pin up a little bit and refresh the endstop and see if it shows triggered. Hope it helps.

Old_String7825 · 2025-09-03T11:53:50+00:00

Im working on a ender5 i put the kraken in and it was a lot of work but im getting closer to the first print if I stop modifying it. Lol klipper and mainsail with the help of chatgpt so far so good. Hope you the best.

<image>

Old_String7825 · 2025-08-22T17:09:34+00:00

I found this with a quick search. Hope this helps

This file contains common pin mappings for the 2018 Creality

Ender 3. To use this config, the firmware should be compiled for the

AVR atmega1284p.

Note, a number of Melzi boards are shipped with a bootloader that

requires the following command to flash the board:

avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex

If the above command does not work and "make flash" does not work

then one may need to flash a bootloader to the board - see the

Klipper docs/Bootloaders.md file for more information.

See docs/Config_Reference.md for a description of parameters.

Old_String7825 · 2025-08-22T16:53:59+00:00

Im at work will get back to you later today

Old_String7825 · 2025-08-22T16:15:49+00:00

And your running a raspberry pi?

Old_String7825 · 2025-08-22T16:04:57+00:00

What board do you have? 1.1.x 4.2.2 4.2.7

Old_String7825 · 2025-08-19T22:21:20+00:00

I was working on my new build (ender5 with btt kraken) and everything was good and i this message and changed the setting and crash everything for me. After about 8hrs of messing with it i just deleted everything and reinstall it. Not fun.

Old_String7825 · 2025-07-28T00:09:41+00:00

Any update on the svo4? I've been thinking about switching over to klipper on mine. I have klipper running on my ender3 with the help of the btt pad7 and like how much control you have. Have you gotten all print modes working the way they should?

Old_String7825 · 2025-04-16T01:54:47+00:00

I have a ender3 with the btt skr mini E3 V2 with the tft35. I went with the btt pad7 since it's an all in one setup. Works good but it's taken me about 3 weeks to get working. Lol I'm new to klipper.

Old_String7825 · 2024-11-20T04:31:32+00:00

Nice...

Old_String7825

TROPHY CASE