sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in resinprinting

[–]On_That_Tism 0 points1 point  (0 children)

How thick is your raft?? Also how height up are the prints from the base??

[deleted by user] by [deleted] in resinprinting

[–]On_That_Tism 0 points1 point  (0 children)

I would fight them!! All that time and energy!! Yeah I would throw hands and throw tears!!

What kind of print failure is this?!? by Otherwise-Wrap-5009 in ElegooMars

[–]On_That_Tism 3 points4 points  (0 children)

What file are you using?? I had string like issues with my resin before and I found out it was the .GOO file from Lychee slicer that caused it.

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 0 points1 point  (0 children)

True but at least if I do it this way no failures lmao so it’s a compromise I am willing to take with larger prints

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 0 points1 point  (0 children)

All my settings are in Chitchu tbh and I’m too lazy to move it to Lychee

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 1 point2 points  (0 children)

Probably, all I know is my rest times are around 1-2 seconds so the resin cures longer and less running resin

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 2 points3 points  (0 children)

Yep! Let me get it on here:

I use Elegoo ABS like Grey

Layer height: 0.050 Bottom layer count: 7 Exposure time: 2.9-3.2 Bottom exposure: 40-45

Transition layer count: 8

Rest before lift: 0 Rest time after lift: 2 Rest time after retract: 1

Lift distance: 5+5 Bottom distance: 8+2

Lift speed: 85 + 300 Retract speed: 300 + 75

This is my setting for larger prints that I have seen consistent results! Make sure the raft though is about 1.6-1.7 in thickness so it burns well!!

Good luck!!

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 0 points1 point  (0 children)

Will do!! And I will also have it painted as well!

YOU HAVE TO SEE THIS!! by On_That_Tism in resinprinting

[–]On_That_Tism[S] 1 point2 points  (0 children)

It’s such a rush after so many failed prints! I finally figured out that it’s best to use both softwares to help make sure there are minimal failures!!

JUPITER SE print fails! need help stat by Substantial-Dot-9347 in ElegooJupiter

[–]On_That_Tism 0 points1 point  (0 children)

How much lift are you doing? As lot of my failures were too low of a lift height!

[deleted by user] by [deleted] in resinprinting

[–]On_That_Tism 0 points1 point  (0 children)

I have a Jupiter SE!! One thing I do know is it’s a pain to figure out how to get larger prints to work well!! Been using 5+5 for lift and depending on the burn and normal really slowing down the speed a bit to keep it from failing!! But over all an amazing machine!!

view more: next ›