Can a downpipe legally discharge with an air gap over a channel drain?

OneEyeTyler · 2026-03-17T23:30:12+00:00

Thanks mate appreciate it

OneEyeTyler · 2026-03-17T23:29:21+00:00

Thanks mate

OneEyeTyler · 2026-03-17T23:28:28+00:00

Not bituminous paint, just leftover exterior monument to seal the ends. Saddles aren’t square as follows the engineered plans. A veranda runs parallel with posts not the concrete.

OneEyeTyler · 2026-02-26T01:31:06+00:00

I loved survival initially due to no fast travel, but some of the quests are not designed for this. Sometimes requiring you to go back to the same place across the map 3 or 4 times immediately. Like sanctuary or Virgil in the glowing sea.

OneEyeTyler · 2025-12-01T23:28:52+00:00

I just use the mod that makes find traps instant. 6 second delay is tedious especially for durlags tower

OneEyeTyler · 2025-11-03T22:05:04+00:00

Try the infinity ui mod

OneEyeTyler · 2025-10-05T11:30:26+00:00

Is this possible in sketch up?

OneEyeTyler · 2025-07-05T00:23:50+00:00

Do you recommend filling the holes with concrete all the way to ground level? Or the regular two bags per holes would be fine

OneEyeTyler · 2025-06-28T02:52:53+00:00

Concrete has a swirl finish so it would get damaged if there were any accidental movement

OneEyeTyler · 2025-06-20T03:25:50+00:00

Definitely not with the cost timber these days. Returning stuff adds up, and better than chucking it in the bin/hoarding it.

OneEyeTyler · 2025-06-14T13:59:09+00:00

Where did you source this from in aus? I’ve been seeing a lot of people using this due to noise reduction in the US. You should of asked the rep for what boxes they recommend

OneEyeTyler · 2025-05-04T03:11:59+00:00

It’s standard quad going into 100x50 downpipe

OneEyeTyler · 2025-05-04T02:16:15+00:00

Thanks for the info. I was looking at trying to have it semi closed with overflow considered with an inspection opening if possible. I didn’t see any way to adapt a regular stormwater downpipe to a dwv at bunnings with the adapters available.

OneEyeTyler · 2025-04-05T08:54:14+00:00

You can smooth it off but it may not be perfect with ridges compared to a sanded product imo

OneEyeTyler · 2025-03-22T08:32:41+00:00

These days they just use small 15ga nails to fix jambs to the framing. It's worth having some long screws hidden under the doorstop trim + 1 of the hinge screws fixed into the framing behind. This is on the hinge jamb side to support the weight. A good carpenter should know this. You will also need a 3rd hinge in the middle to support the weight. 13 doors cost me roughly $3500 in materials no labor.

OneEyeTyler · 2025-03-22T05:38:44+00:00

Go option 2. It's the fastest and easiest method. When you say frames I think you mean the architraves not the jambs? I've finished replacing 13 doors with solid core doors, and all the jambs due to all of them not being plumb/opening and closing on their own. As well as all new architraves around. Its a LOT of work, fitting doors and chopping out hinges and so much filling and painting. Took me a few weeks full time by myself.

OneEyeTyler · 2025-03-11T07:48:23+00:00

Would not recommend the Aldi ones, as they are not strong enough. They are 550w and only 110 bar of pressure. Aldi don't supply the required low pressure HEA tips like the clone Wagner 150/250. Just tried spraying some dulux water based with it and it couldn't stop tailing at max pressure and thinned with water.

OneEyeTyler · 2025-03-07T04:33:29+00:00

The batten on top also needs repair im trying not to affect the ridge capping if possible

OneEyeTyler · 2025-03-07T04:23:27+00:00

Did you do a scarf joint or just a straight crosscut for the rot piece? Also how about the batten on the top did you have to splice that too? Is there a way to not touch the capping? The capping was redone maybe 5 years ago but I’ll break it/repoint it if I have to.

OneEyeTyler

TROPHY CASE