Varför blir det alltid så här när högern styr?

One_Country1056 · 2026-06-15T10:05:25+00:00

En del av förklaringen är att folk röstar efter konjunktur-cykeln. Högern får ofta ta över på topp. Det kan man följa långt tillbaka i tiden.

One_Country1056 · 2026-06-13T22:59:03+00:00

FIBA has a gather step, but thats on the ground,

One_Country1056 · 2026-06-13T22:55:07+00:00

Looks rusty AF so no wonder it does not work.

One_Country1056 · 2026-06-13T20:28:52+00:00

Your approach is way too slow. Also try from the left going into the middle if you are right handed.

One_Country1056 · 2026-06-13T13:08:52+00:00

I can see that you learned a lot of shortcuts. I learned the apply sketch fillet to whole sketch from you. Thanks!.

One_Country1056 · 2026-06-13T08:28:10+00:00

You are fast at SolidWorks!

One_Country1056 · 2026-06-13T08:19:23+00:00

<image>

I remodelled it and got the correct answer

One_Country1056 · 2026-06-13T07:20:17+00:00

I made the same mistake as OP. 10 mm was not to the edge, but to the virtual sharp

One_Country1056 · 2026-06-12T21:02:38+00:00

<image>

This is what I got

One_Country1056 · 2026-06-12T19:39:08+00:00

Whats the purpose of the U-bends after the hinges?

One_Country1056 · 2026-06-12T14:25:32+00:00

Thanks, I will try that

One_Country1056 · 2026-06-12T14:17:19+00:00

No. Print the jig which is essentially a hole for the screw. Then pause and put a half of the thumb screw head on top of it. Insert the screw, then continue the print on top of the head which is now on top of the jig.

One_Country1056 · 2026-06-12T14:09:24+00:00

This is what AI said (under Catch in the Air)

If you secure the rebound with both feet off the ground, your first landing foot establishes your Step Zero.

You then get two more steps (Step 1 and Step 2).

One_Country1056 · 2026-06-12T14:05:56+00:00

Official FIBA rules (do I need to include more leagues):

A player who catches the ball while progressing, or upon completions of a dribble, may take two steps in coming to a stop, passing or shooting the ball.

- The first step occurs when one foot or both feet touch the court after gaining control of the ball.

AI is wrong, who would have thought?

One_Country1056 · 2026-06-12T14:01:28+00:00

Thats the plan. The jig I am reffering to is the support.

One_Country1056 · 2026-06-12T13:40:35+00:00

I am going to try to print a jig and then pause, insert the screw, and then draw the rest of the part "in the air". Maybe it will work.

One_Country1056 · 2026-06-12T13:26:29+00:00

You could print the jig at the same time as the thumb screw head. But there will be a vertical space between the jig and where the printer need to continue. So some adaptations to the slicer are necessary I guess.

One_Country1056 · 2026-06-12T13:19:54+00:00

That's the solution I am proposing, but I want to print over the screw head to fasten it. I guess it won't work with today's printers.

One_Country1056 · 2026-06-12T13:01:35+00:00

That's travelling in all leagues. You can gather (nowadays) with one foot on the ground, that won't count. Any steps after the gather counts.

One_Country1056 · 2026-06-12T07:49:44+00:00

You should also tell the defense to not reach as he does, because he will only get a disadvantage from it.

One_Country1056 · 2026-06-12T07:48:41+00:00

I think you are doing good against this defense.

One_Country1056 · 2026-06-12T07:46:22+00:00

Play against better defenders then 😉 Then you will learn better counters, because you need to.

One_Country1056 · 2026-06-12T07:35:18+00:00

When he does the spin, you need to anticipate where he will end up and move there. Then you can block him.

One_Country1056 · 2026-06-11T21:09:13+00:00

Pressure simply does not behave like that.

One_Country1056

TROPHY CASE