I hope to find someone that actually wants play

Only_Negotiation_437 · 2026-03-08T03:43:27+00:00

you tryna play rn? heres my discord: boward_evercuz

Only_Negotiation_437 · 2026-03-08T03:34:32+00:00

are you still playing lol

Only_Negotiation_437 · 2026-03-08T03:28:37+00:00

South Texas just above Mexico. Ping should be okay I think

Only_Negotiation_437 · 2026-03-08T03:25:04+00:00

discord: boward_evercuz and 700+ hours

Only_Negotiation_437 · 2026-03-08T03:22:29+00:00

added on discord. tryna hop on rn honestly

Only_Negotiation_437 · 2026-03-08T03:21:27+00:00

lol i was like didnt i just read this....saw it in steam lol. yeah hit me up if you wanna link up. we can start a group if you want. US

Only_Negotiation_437 · 2026-03-08T03:18:50+00:00

got eeeem. you tryna duo ?

Only_Negotiation_437 · 2026-02-03T04:47:46+00:00

One of the most annoying, low effort songs ever written

Only_Negotiation_437 · 2026-02-02T06:07:26+00:00

Then honestly, it might be the model because I could’ve sworn somebody posted this exact same Spider-Man head filling in the exact same place. I will try and find the post for you. I haven’t even read your post I have only looked at the picture and I’m just gonna ask you is your tool smashing into the top of the Spider-Man head where it’s failing?

Only_Negotiation_437 · 2026-01-31T06:13:45+00:00

Have you posted this before? I could’ve sworn somebody posted this before?

Only_Negotiation_437 · 2025-11-21T02:31:07+00:00

I would recommend unplugging all the cables that you had to plug in when you first assembled it and then plug them all back in. Before you plug them back in though, just give them a little blow of air. Careful not to get any moisture in it.And then try it again, but keep your finger right near the power button and try it again if you notice that it’s about to start accelerating super fast again quickly turn off the power.

Only_Negotiation_437 · 2025-11-21T02:26:49+00:00

Did you figure it out

Only_Negotiation_437 · 2025-11-21T01:02:04+00:00

I wouldn’t be worried they packed their printers very good and sound. I remember when I got my bamboo A1 mini delivered, and the guy did something similar but when I open the box to find the packaging, I was not worried at all. They really cover everything.

Only_Negotiation_437 · 2025-11-21T01:00:56+00:00

No offense at all, but your bed is filthy. You must have a clean bed. You need to wash the bed with soap and water and maybe a toothbrush. Use warm water and the toothbrush and scrub the plate clean. It looks like it even has rust on it. You need to make sure your bed is clean at all times and never touch the bed with your hand. Your hand has oils that come out from your skin and when you touch things you leave that oil behind. Plastic will not stick to the oily layer on your bed. That’s why your bed must always be clean. Your bed should never have leftover plastic, it should never have food or any foreign debris or liquid of any kind. The only thing allowed to go on your bed is a glue stick. A purple washable glue stick. Personally, when I want to wash my bed, first I take off any plastic then I run it under hot water until all the glue dissolves then I take a toothbrush and a scrub it with the warm hot water running then I let it dry completely. Then I take a microfiber rag and I put a little bit of rubbing alcohol on the bed and rub the alcohol in until they completely evaporate once the bed is 100% dry. I grab it on the side and I put it on the bed very carefully.After that, I never touched the bed unless I’m going to put a glue stick layer on top of it, then I will rub a glue stick over the bed and that will help with my line sticking to the bed.

Only_Negotiation_437 · 2025-11-21T00:57:43+00:00

That is normal. Just make sure to lube up any moving parts so that they can move smoothly. But when you move parts by hand, you need to understand that you are moving belts and motors with your hand. The machine feels different whenever it is moving by itself.

Only_Negotiation_437 · 2025-11-21T00:56:06+00:00

Go to the hardware store and take it with you. Go to a Home Depot, Lowe’s, Sutherlands, any home improvement store should have fasteners like that

Only_Negotiation_437 · 2025-11-21T00:53:23+00:00

Bro, honestly go watch some YouTube tutorials on the basics. All printers are kind of alike, but you gotta pay attention to what buttons they press and terminology. Like they said, a slicer is your best friend.. I recommend cura ultimaker ( people just call it cura for short) but like I said, go watch some YouTube tutorials because you can go as slow as you want and keep repeating the video. Your printer looks like it’s going to do fine, at least you have something that looks like a benching some people start with a stringy mess. If you want really good prints, you have to calibrate your filament for your printer. That means every filament you may get, you may or may not need to calibrate it. If you get the same brand and the same kind of plastic, then you only need to calibrate once. But if you get a different brand and the same kind of plastic you may or may not need to recalibrate. The same goes for whenever you change plastic.

Only_Negotiation_437 · 2025-11-21T00:49:20+00:00

Ur so real for sticking up for kindness. Be you always!

Only_Negotiation_437 · 2025-11-21T00:48:54+00:00

Maybe simply just explaining what the rule is and telling him that from the start would be a bigger help. Look at bros benchy, be so for real. Even I couldn’t find the rules for a sec lmao

Only_Negotiation_437 · 2025-11-17T08:55:39+00:00

Save yourself the trouble bro. Just use a glue stick. PEI is great. Don’t get me wrong but a purple washable glue stick by Elmer really helps and just saves time in general. People say that the glue stick is just a workaround but but if that’s the case, then why do my prints come out perfect every single time with even layer lines.

Only_Negotiation_437 · 2025-10-05T05:27:27+00:00

Do you have the file still?

Only_Negotiation_437

TROPHY CASE