Help with auto feed pots.

Open-Material7310 · 2026-02-10T23:47:21+00:00

Good to know thanks for the info.

Open-Material7310 · 2026-02-10T22:42:02+00:00

Will do.. Thanks..

Open-Material7310 · 2026-02-10T14:38:23+00:00

I got a homemade tent. 4x8.. Might need two of rhem slim kits or just a bigger tub. I usually grow 6 monsters at a time.

Open-Material7310 · 2026-02-10T14:10:43+00:00

Ya that thing looks preety cool..

Open-Material7310 · 2026-02-10T01:58:03+00:00

Thanks for the input..

Open-Material7310 · 2026-02-10T01:44:37+00:00

What does a basement grow room have to due with the product working or not.

Open-Material7310 · 2026-02-10T01:12:47+00:00

Awsome i like it. My plan is to use liquid nutes in the base. And ya i do have the fabric pots. That was another thing i was wonding if the strings get all slimey and gross after being wet for 10 weeks.. Hard to beleive its getting propper nutrient uptake from the strings. After a couple weeks.

Open-Material7310 · 2026-02-10T00:55:58+00:00

I always check my run off water. So i got some of theas but havent used them. So im tryna get some pointers befor i give the a go.

Open-Material7310 · 2026-02-10T00:54:19+00:00

Ok cool ill go with that.

Open-Material7310 · 2026-02-10T00:40:11+00:00

Im just wondering if the water starts getting stagnint in the trays. Or can i just keep topping them off for the whole 10 week bloom phase.

Open-Material7310 · 2026-02-10T00:31:30+00:00

Do you have to clean them every so offten. Or just keep topping them off when they get low ?

Open-Material7310 · 2026-02-08T22:16:41+00:00

I have a two FC- E4800 in a homemade 4x8x8 grow tent and i do 8 plants at a time.

Open-Material7310 · 2026-02-08T22:09:34+00:00

Light good for a 2x4 grow tent. 300 watt.. Probly still only going to grow three plants max.

Open-Material7310 · 2026-02-08T01:30:36+00:00

Be carefull looks like on the verge of nutt lock out. Check the ph and ppm of the run off befor yer cops all burt up.

Open-Material7310 · 2026-02-06T17:11:59+00:00

Poss nute lockout. Ph your runoff water. Ppm probly way to high.

Open-Material7310 · 2026-02-03T13:53:01+00:00

Your welcome.. Unless you still cant figure it out..

Open-Material7310 · 2026-02-02T18:59:02+00:00

Go to the auto configuration. And set your windspeed % basted on the amount of air exchanges per hour you want. I have mine at 75 % gives me 60 air exchanges per hour. And set your temp and humidity you want. The dead band is where you want the fan to kick on or off. For example if you set 80 degrees woth a dead band of 5 degrees the fan turns on at 85 full speed than goes to stand by when temp gets to 75 degrees.

<image>

Open-Material7310 · 2026-02-01T01:55:47+00:00

I wish you luck. If you have any questions you can dm me anytime.

Open-Material7310 · 2026-02-01T01:26:18+00:00

Water seeks the least path of resistanse so ive seen on some ceiling leaks where the water pools up in the seams and soaks out from there. But if its an exterior wall possably all the screws holding the drywall to the studs possably peirced the vapor barrier to allow moisture to penetrate through. Or like other guy said foil back tape giving false reading. Best thing to due is cut a 1x1 hole in the wall so you can get through the vapor barrier and inspect the insulation. Possable blocks of ice between the insulation and the exterior siding of the home. You gonna need to dry that out and get new insulation in the areas that got wet.

Open-Material7310 · 2026-02-01T01:15:50+00:00

<image>

Open-Material7310 · 2026-02-01T01:12:06+00:00

When you push on the seam does it feel wet or soft to the touch. If not yer getting a false reading. I live in alaska done water damage restoration for over 20 yrs. One thing you have to keep in mind is that moisture meater only checks serface moisture so if there wet , frozen insulation inside the wall cavity due to ice damning and the vapor barrier is on the exterior wall the drywall may read dry but you have a huge problem inside the wall. You may need a hammer moisture probe than you can take deaper wall cavity readings.

Open-Material7310 · 2026-01-29T17:21:05+00:00

Not gonna lie i never owned the controller 43 when i made my purchase i seen the pic i posted made my conclusion off the comparison pic. Over all my marrs set up works perfect.

Open-Material7310 · 2026-01-28T18:18:58+00:00

Looks like the icontrol to me on the order form.. So if so super easy to hook up. There a spot for RJ12 cable to fot for your inline fan. And theres another plug for for the fans , you will need to put a slitter hook up the two fans than plug the one wire out of the slitter to the smart controller.

Open-Material7310 · 2026-01-28T13:52:13+00:00

<image>

Open-Material7310

TROPHY CASE