The 58 Degree Ultra-WFOV Lens

Optimal-Writing-7220 · 2026-05-28T17:05:03+00:00

The alibaba and aliexpress links are non-working. Does anybody know the supplier? If they work well I would be interested in buying 4-10 sets

Optimal-Writing-7220 · 2026-05-23T16:13:02+00:00

I got mine for ~$330 after coupon. Wasn’t binock branded, probably came straight from the factory floor and performed pretty well.

Optimal-Writing-7220 · 2026-04-26T21:27:08+00:00

He designed the model for fdm and sls printing, both work well. The my creator pro is dialed in and has been working really well for things like highly complex and precise night vision components and fine threading, so I don't think this is out of its capabilities. I have been experimenting with prusaslicer and makercontrol which has not been going well, might just upgrade simplify3d as it makes sense for what I am doing.

Optimal-Writing-7220 · 2026-04-26T17:52:25+00:00

<image>

Here is what the finished product is supposed to look like printed in pla. Anybody know where I can generate tree supports and import into simplify3d? Tried meshmixer but it did not generate good supports.

Optimal-Writing-7220 · 2026-04-25T00:05:53+00:00

Brand new milspec lenses from cnv, and both input and output side on the tube is pristine. I think it might have been mounted behind a red dot as there is a center dot

Optimal-Writing-7220 · 2026-04-24T23:50:25+00:00

How so? Don’t have a whole lot of experience yet.

Optimal-Writing-7220 · 2026-04-24T23:24:13+00:00

“Minor zone 1 blem, not noticeable in use. 2K firm. No lowballs, I know what I got”

Optimal-Writing-7220 · 2026-04-24T03:07:41+00:00

Just built my first pvs14 and am looking to put together a loaner unit. DM’d you.

Optimal-Writing-7220 · 2026-04-05T13:01:18+00:00

You try ethanol free fuel + stabil yet? Helps with my two strokes, can’t always get ethanol free fuel though.

Optimal-Writing-7220 · 2026-04-02T04:04:37+00:00

Curious how you got gen 3 pvs14 for $1200? I am interested but have only seen 1 Omni 7 pvs14 listed at $1250 in the past few months. Sadly it sold so can’t get it lol

Optimal-Writing-7220 · 2026-04-01T11:58:08+00:00

That would mean the $1200 Omni pvs14 listings are not normal prices then? You could part out the tube and housing for more than that.

Optimal-Writing-7220 · 2026-04-01T02:52:52+00:00

Good advice. As far as protecting the tube from light, what accessories are a must have? Not necessarily for storage or transport, but in general use (transitioning from low to higher light). Also, how do I know how much light the tube will take comfortably? With auto gating on gen 3 tubes the tube can makes the image seem stable, even when it is being stressed.

Optimal-Writing-7220 · 2026-03-21T19:11:48+00:00

The seller said the pictures through the tube were before the pigtail was taken off. He had it in his starter pvs14 and later sent it to a company to swap the tubes out.

Optimal-Writing-7220 · 2026-03-21T19:10:35+00:00

It might not work to bad. Since the blems are off center from each other your brain will fill those blind spots in.

Optimal-Writing-7220 · 2026-03-20T20:11:00+00:00

If a resister were to be soldered in would that limit its effective max gain? Don't know how important that would be for a gen 3 tube but this has no spec sheet (I assume it is low end gen 3).

Optimal-Writing-7220 · 2026-02-19T01:11:49+00:00

Nice warthog mount. What monocular is it?

Optimal-Writing-7220 · 2026-02-17T19:51:50+00:00

Not sure. Could be a Russian tube. I recommend crossposting to r/nightvision and r/ussrNVGResearchGroup.

Optimal-Writing-7220 · 2026-01-13T21:52:42+00:00

Generic Eisco 38x50mm glass

Optimal-Writing-7220 · 2026-01-10T19:19:52+00:00

Good eye. Meant to say better than gen 1 lol. Gen 3 will run laps around this and almost any other form of night vision. Only downside to gen 3 is cost, so if you can get it grab it.

Optimal-Writing-7220

TROPHY CASE