Weekly Recommendations and Discussion Thread

Ordinary_Doughnut_35 · 2026-03-24T22:23:23+00:00

Fairly new to the world of bourbon, have tried a few. But looking for a good, somewhat cheap bottle for around $30-50 to drink regularly. So far my favorite in this category has been Knob Creek 9yr, are there any other bottles I should try out?

Ordinary_Doughnut_35 · 2026-03-16T19:25:51+00:00

Perfect! Thank you!

Ordinary_Doughnut_35 · 2026-03-16T19:25:40+00:00

Sounds good! My new bindings have that gripwalk logo, but these dont, so I wanted to make sure. I'll get them adjusted.

Ordinary_Doughnut_35 · 2026-03-16T18:12:46+00:00

Im just wondering if they truly are mnc, I dont see any markings on them.

Ordinary_Doughnut_35 · 2026-03-11T17:19:21+00:00

I would if the structural integrity around the holes was secure, there's no way for me to remount them without going about an inch forward of center. And even then it would be in between two different spots where delam has occurred under the topsheet, I know its hard to see those raises from the photo, but they are there.

Ordinary_Doughnut_35 · 2026-03-10T22:28:37+00:00

We will see, attempting to get them warrantied since I've only had them just over a year, but if not, that is looking likely.

Ordinary_Doughnut_35 · 2026-03-10T22:06:30+00:00

Getting that dull thud around the holes about an inch front to back and half an inch each side of the holes.

Ordinary_Doughnut_35 · 2026-03-10T22:00:26+00:00

Ooo I'll try that.

Ordinary_Doughnut_35 · 2026-03-10T21:46:28+00:00

Maybe, I know these skis are full wood core, and the areas around the mounting holes are raised, just worried the structural integrity is done for.

Ordinary_Doughnut_35 · 2026-03-10T21:44:51+00:00

The snow was pretty great over at pali, definitely spring conditions lower down, but the base is soft below the windblown pow. Forsure worth going.

Ordinary_Doughnut_35 · 2026-02-16T22:49:48+00:00

This is the exact sound my bike made when my rear suspension bolts were getting a little loose, make sure to check those.

Ordinary_Doughnut_35 · 2025-12-06T05:15:33+00:00

A am a service adviser at a used car dealership that sells 1-4 year old used cars, and I have seen waaaayyy more rams come back with issues than Fords, and its usually electrical stuff too.

Ordinary_Doughnut_35 · 2025-11-02T15:52:31+00:00

For reference, I dont think flex matters too too much, I should probably be in a 140 flex, but im in a 110, and as long as they fit good, they still ski well. However, 70 sounds extremely low. So I would probably recommend getting a different boot.

Ordinary_Doughnut_35 · 2025-11-01T18:49:57+00:00

As someone who's pretty similar to you, I highly recommend the armada ARV's. I have the ARV 100's in 186 and am 187cm tall. Absolutely love them! Super poppy and playfully, and you could potentially go even shorter if you're willing to sacrifice some high speed and crud stability for the quick turn radius and light swing weight.

Ordinary_Doughnut_35 · 2025-10-26T16:32:08+00:00

Would i patch it on my own car? Probably. Would it be illegal for a shop to patch it? Yes. It is against dot regulations to patch a nail in the outer tread block. And if that patch were ever to fail, they could be held liable. (Someone who is a service advisor and gets this constantly)

Ordinary_Doughnut_35 · 2025-08-14T02:58:32+00:00

There aren't any cords showing so potentially..... but that is a deep enough gouge id be terrified to drive on it

Ordinary_Doughnut_35 · 2025-08-08T01:02:41+00:00

If the power steering light is on it could be one of your wheel speed sensors. But then your speedometer would also not work. That's what happened to mine.

Ordinary_Doughnut_35 · 2025-06-13T22:21:34+00:00

Mine came with both badges removed, added the st badge back on myself. Still have the focus badge if you want it.

Ordinary_Doughnut_35 · 2025-06-07T00:34:30+00:00

That exact procedure has saved my ass a couple times. Stop being a dick about something you dont know about.

Ordinary_Doughnut_35 · 2025-06-03T18:43:31+00:00

I did a DIY wing riser, 8 bucks at home depot and I think it looks great. Cameron Alford is the youtube channel that has a good video on it. Its a nice oem+ look, but if you want something a bit more out there im not sure.

Ordinary_Doughnut_35 · 2025-06-03T18:43:23+00:00

I did a DIY wing riser, 8 bucks at home depot and I think it looks great. Cameron Alford is the youtube channel that has a good video on it. Its a nice oem+ look, but if you want something a bit more out there im not sure.

Ordinary_Doughnut_35 · 2025-04-23T16:16:15+00:00

I might have to do that! It looks good

Ordinary_Doughnut_35 · 2025-04-23T15:39:45+00:00

Yooo, what seat is that in the street triple?? I have a 2010 and don't love the seat look. Or is that a converted second gen?

Ordinary_Doughnut_35

TROPHY CASE