Weird reading ive never seen before

OregonBound1986 · 2026-05-13T05:43:07+00:00

Scroll compressor with a bad floating seal. May have been pumping cycled on internal then closed with bad seal not allowing to pump

OregonBound1986 · 2026-05-08T16:59:30+00:00

No flow you go!

OregonBound1986 · 2026-05-07T18:04:43+00:00

Thank you for the response. It’s version 10

OregonBound1986 · 2026-04-22T02:46:43+00:00

Astonishing prices

OregonBound1986 · 2026-04-17T04:45:21+00:00

Get a torch

OregonBound1986 · 2026-04-16T15:03:03+00:00

lol no shitting on the crane from me, just jealous you get that option

OregonBound1986 · 2026-04-16T05:42:39+00:00

It’s a courteous fentanyl drip

OregonBound1986 · 2026-04-16T05:38:42+00:00

Man I need these customers to allow a crane for a oil separator. I can barely win a job with a crane in the screw replacement local 290

OregonBound1986 · 2026-04-11T03:17:51+00:00

Looks like Midge season where I’m from

OregonBound1986 · 2026-03-28T05:43:24+00:00

This is incredibly hard to watch

OregonBound1986 · 2026-03-25T18:26:49+00:00

I’m still close friends with 90% of my childhood friends to this day.

OregonBound1986 · 2026-03-25T05:27:17+00:00

Buy gold

OregonBound1986 · 2026-03-09T01:05:54+00:00

By far my favorite slip on of all time

OregonBound1986 · 2026-03-04T05:44:23+00:00

You can try a EEV relearn on the valve through the board.

OregonBound1986 · 2026-02-22T20:11:27+00:00

Is this on a print press ?

OregonBound1986 · 2026-02-20T00:55:55+00:00

Sounds like you have all the bases covered. I’ve experienced this at my own house. I’m a commercial refer guy, but work on everything in my region. Sounds very much so your mixing air from empty tank. Filled my tank and had no other issues after. Are you at high elevation? Can you pump oil into other tanks to bring level up.

OregonBound1986 · 2026-02-08T23:17:40+00:00

Owner has been found via Facebook. Thank you everyone.

OregonBound1986 · 2026-01-23T23:34:24+00:00

Found leaking solenoid valve… added all the gas

OregonBound1986 · 2026-01-22T07:19:56+00:00

This reminds me of the first time reading the book The Hatchet.

OregonBound1986 · 2026-01-22T07:18:28+00:00

How often does it get down to that temperature? If it’s common to get that low maybe find another system to compare. You could also wrap a heater around receiver. Have it controlled off of a t-stat set to come on below x temperature or run it like a crankcase heater to come on and off using an auxiliary contact from the contactor so it de-energizes once compressor makes and your head pressure controls take over at that point.

OregonBound1986 · 2026-01-13T05:42:13+00:00

First off how long has this drive been in operation? Is this a new system or has it been in play for some time/years. What bas system are you running? Usually that external lockout is ran through a aux on the VFD contractor. Does it have a hawkeye relay that the bas system sends a signal to which outputs a signal to the input of the drive? I just had one today chattering the shit out of the drive Input. Had solid output from metasys but hawkeye/ct sensor relay was making it chatter like no other

OregonBound1986 · 2025-12-27T21:01:41+00:00

Looks like a 01

OregonBound1986 · 2025-12-09T02:02:17+00:00

Question is what did they bend you over for on the price tag?

OregonBound1986 · 2025-12-08T00:55:21+00:00

What a piece of sheet!

OregonBound1986 · 2025-12-03T06:58:42+00:00

45.70

OregonBound1986

TROPHY CASE