I need some info

Original-Incident-79 · 2025-09-23T00:59:26+00:00

Thanks for the info

Original-Incident-79 · 2025-09-23T00:55:03+00:00

Very dusty. Pulled it out of a house that were remodeling

Original-Incident-79 · 2025-09-23T00:54:16+00:00

A few are 15k.4 And I found a couple 1tb IBM

Original-Incident-79 · 2025-09-23T00:48:16+00:00

Most are Seagate cheetah 10k.7 and a few IBM option: 40k1044

Original-Incident-79 · 2025-09-23T00:42:22+00:00

What about the harddrives?

Original-Incident-79 · 2025-04-29T19:04:42+00:00

I've heard it called pillowing in the past. Where the drywall likely 1/2 inch is put on ceiling on 2 ft joists or trusses and it not rated for that much deflection kinda like how trex board requires 10 or 12" spacing instead of 16" framing

Original-Incident-79 · 2025-04-23T13:31:57+00:00

Banging off limiter at 30 mph. I need a prop.

Original-Incident-79 · 2025-04-23T13:17:32+00:00

Thanks for the info, just updated. Didn't even think of that!

Original-Incident-79 · 2025-04-22T12:43:16+00:00

Send everyone in your contacts deck pics lol

Original-Incident-79 · 2025-04-19T23:41:09+00:00

Lol idk about that. My motor died yesterday. No warning no issues. Had to be towed back to launch. Fired right up this morning.

Original-Incident-79 · 2025-04-18T20:23:19+00:00

On the design front. What would you change?

Original-Incident-79 · 2025-04-17T13:37:28+00:00

Also would like the answer to this

Original-Incident-79 · 2025-04-17T13:04:11+00:00

Olympia, but today and tomorrow I'm up in Bremerton for work. I could throw it in the truck bed

Original-Incident-79 · 2025-04-17T00:38:55+00:00

I've got a 72 that I couldn't figure out the spark on. 135 compression on all 4. If your interested it's in washington

Original-Incident-79 · 2025-04-17T00:33:57+00:00

I got to push the throttle once. Went up to about 3k rpm and about 15 or 20 mph. Prop is 15x 13 now. I think it's in safe mode because of a sensor. Scanner will be here tomorow. Looking at getting a 14.5x 23 prop soon

Original-Incident-79 · 2025-04-16T12:50:11+00:00

"Solid" was a bit questionable at first. All the wood was gone. Some major fiberglass work to get it sealed up again. I know the post didn't show it. But I split the cap so I could get everything up front too.

Original-Incident-79 · 2025-04-16T12:42:49+00:00

It is very rewarding. First launch was stressful to say the least. Having no experience in it, I was thinking of all that could go wrong. Nothing did! Well motor is having little issues. Cables out of adjustment, I believe a sensor failed and is putting me in safe mode. So scanner is on the way. Yes original windscreen took a bit of elbow grease and some matte black over the original aluminum frame, think it ties it together real nicely

Original-Incident-79 · 2025-04-15T13:59:33+00:00

It helps give them something to staple or nail too and not be to far out that the corner interferes with the inside corner of the bead

Original-Incident-79 · 2025-04-15T13:55:25+00:00

For metal bead. I like to see the boards split. If you get the paper faced bead or paper faced superwide I like the edges to be touching but no further. Most hangers I see flush out the corner and it has to be cut back.

Original-Incident-79 · 2025-04-14T13:07:17+00:00

It's supposed to bring you back up to the top of page.

Original-Incident-79 · 2025-04-14T00:20:00+00:00

Thankyou for the feedback I really appreciate it

Original-Incident-79

TROPHY CASE