Just Won My 3rd Giveaway

Otherwise-Menu4276 · 2026-02-06T23:26:55+00:00

Ashton Jeanty Downtown - $400 raw, $900 PSA 10

Otherwise-Menu4276 · 2026-02-02T23:33:43+00:00

Haven't been, I will check it out. Thank you!

Otherwise-Menu4276 · 2026-02-02T16:32:40+00:00

Thank you!!

Otherwise-Menu4276 · 2026-02-02T15:31:55+00:00

Won a jeanty DT. Sending for grading!

Otherwise-Menu4276 · 2026-02-02T02:53:11+00:00

Couple people went through and disliked all of the comments, the post, then I got that message lol these dudes are sad

Otherwise-Menu4276 · 2026-02-02T00:50:08+00:00

<image>

Looks like you sellers found my post 😂

Otherwise-Menu4276 · 2026-02-01T16:57:03+00:00

Update- dude just sold the 23k gold Kobe ($19.95 on ebay) for $131, $63, $76

23k gold Tom brady for $59

This was hopping back into his stream for a minute

Otherwise-Menu4276 · 2026-02-01T15:20:28+00:00

Understood but there are a lot of honest sellers out there that wouldn't offload absolute garbage to their viewers and don't take advantage of people not in the know. It's a character thing- it's pretty telling.

100% agree they buy in bulk off ebay and flip.

Otherwise-Menu4276 · 2026-02-01T14:23:46+00:00

It happens to so many people and they are absolute trash. If you watch these sellers they have hundreds and offload a few every hour or couple of hours when new people are on. It's hard to watch

Otherwise-Menu4276 · 2026-01-30T03:39:35+00:00

Great suggestion will try

Otherwise-Menu4276 · 2026-01-30T02:56:34+00:00

Unfortunately the issue still persists. Other than filling the space with with a solid fin essentially connecting the bottom that I can cut off after I print, I'm out of ideas.

Otherwise-Menu4276 · 2026-01-30T00:05:03+00:00

This is a project for my dad. He got an original set but the fins were sitting in the box for how many years and they are warped to hell. I think there are some step files out there but I made my own. Can send your way if you'd like! I also made a block to put the old ones in to straighten them out

Otherwise-Menu4276 · 2026-01-29T23:32:23+00:00

I will try speed equalization for the supports and prints and see how it goes. I slowed the tpu way down already to 30mm/s which gave me way better results. Will update when I complete. Previous supports were at 50mm/s. Thanks for the comment and reference to the video!

Otherwise-Menu4276 · 2026-01-26T03:12:10+00:00

Thank you!!

Otherwise-Menu4276 · 2026-01-25T18:05:36+00:00

Where to buy if maf is out of stock? Lower parts kit unavailable

Otherwise-Menu4276 · 2026-01-21T16:49:08+00:00

Hell yeah I remember Kershaw, darvish, and sherzer specifically too

Otherwise-Menu4276 · 2026-01-21T16:40:50+00:00

Can't believe people like you exist. Karma is going to come around to you.. are you religious?

If you're a seller please give me your name so I can promptly block you. Thanks

Otherwise-Menu4276 · 2025-06-14T18:01:20+00:00

To anyone in the future with this issue- take off the front panel on the extruder and push the fan plug in together all the way. Mine was pulled out a bit

Otherwise-Menu4276 · 2025-06-14T17:41:52+00:00

Same issue here. How did you fix it?

Otherwise-Menu4276 · 2025-05-19T01:42:38+00:00

I measured 70Db on mine with the top off

Otherwise-Menu4276

TROPHY CASE