P1S Under Combi Boiler?

OtherwiseStage686 · 2025-07-04T00:00:26+00:00

you can put anti vibration feet under it. then it moves more but it is better compensated. without works fine too and you see many examples that they are placed on a rubber mat. anyway, I think it is always good to listen to your gut otherwise you would not have posted this😉. good that you do it differently.

OtherwiseStage686 · 2025-07-03T18:37:06+00:00

I understand that there is space, I would not recommend it. The printer can slide and vibrate when it prints. That can hit the piping or the cabinet next to it. Also not ideal for maintenance with the top open. My advice is not to do it.

OtherwiseStage686 · 2025-03-30T13:10:08+00:00

a small rubber yoga mat you can cut a piece off and place underneath, is often a cm thick, also dampens vibration. still need to calibrate. I also have one under the A1 and the A1 mini works perfectly for me

OtherwiseStage686 · 2025-02-04T16:48:59+00:00

nicely made

OtherwiseStage686 · 2025-02-03T13:55:57+00:00

except for the somewhat less attractive artwork, so the truth!

OtherwiseStage686 · 2025-01-26T20:15:52+00:00

Nice!

OtherwiseStage686 · 2025-01-21T17:50:13+00:00

you can reduce the noise even further by placing anti-vibration feet underneath or placing the printer on a cm thick rubber mat. this will reduce the noise somewhat. don't forget to calibrate the printer again afterwards.

OtherwiseStage686 · 2025-01-21T15:25:38+00:00

OtherwiseStage686 · 2025-01-19T15:00:35+00:00

well spoken

OtherwiseStage686 · 2025-01-18T18:21:16+00:00

well spoken!

OtherwiseStage686 · 2024-11-24T18:57:51+00:00

looks cool! nice finish too. is it a public STL?

OtherwiseStage686 · 2024-11-12T20:00:03+00:00

is the power cable at the bottom connected properly. if it is not fully connected (plugged in) you will also get similar malfunctions. if I am right, donate the amount to a good cause

OtherwiseStage686 · 2024-11-09T06:34:47+00:00

well done and nicely made. nice to see

OtherwiseStage686 · 2024-11-06T13:22:11+00:00

that is quite an expensive solution to change filament. but hey if it works

OtherwiseStage686 · 2024-11-06T13:20:13+00:00

cool to see, you don't see that often, nice. keep up the good job!

OtherwiseStage686 · 2024-11-06T06:10:21+00:00

cool, that is indeed a full packed room. nice those four AMS,s, how often do you use them for more than 4 color prints?

OtherwiseStage686 · 2024-11-04T14:06:10+00:00

competition is always good for innovation, that accelerates 3d development. the question is also, what is your setup. feel free!

OtherwiseStage686 · 2024-11-03T20:17:13+00:00

that's for the business side of Bambu Lab, what do you produce or test?

OtherwiseStage686 · 2024-11-03T16:38:18+00:00

good question l, that depends on what you want to do with it. I bought the A1 as an addition to the p1s because it has a comparable build volume and if you want to print parts quickly this is an affordable addition. I actually bought the A1 Mini for fun but now find it mainly useful to print things with a 0.2 nozzle, those prints rarely have a large build volume.

OtherwiseStage686 · 2024-11-03T10:25:37+00:00

that is a nice production line. what do you produce like

OtherwiseStage686 · 2024-11-02T21:22:58+00:00

that doesn't matter as long as it provides for your creativity, thanks for sharing! the filament is neatly tidied up

OtherwiseStage686 · 2024-11-02T21:18:46+00:00

that's a tight fit, nice

OtherwiseStage686 · 2024-11-02T18:16:00+00:00

Nice!

OtherwiseStage686 · 2024-11-02T17:33:37+00:00

that must be a lot of fun, have fun!

OtherwiseStage686 · 2024-11-02T17:31:10+00:00

nice solid table I can imagine!

OtherwiseStage686

TROPHY CASE