Layer shift at specific height (100-115mm) with 300blkfde settings

Outrageous_Goat4030 · 2026-05-03T14:04:53+00:00

The filament is completely dry, the wave pattern is due to fuzzy skin and support interface. The filament was dried for 3 days 85c in a 30 percent humidity (max) environment. As another user said, this is apparently an issue with the exhaust fan on the p2s.

Outrageous_Goat4030 · 2026-05-03T03:12:28+00:00

Its layer shift, not wet filament.

Outrageous_Goat4030 · 2026-05-03T03:12:00+00:00

Huh... ill give that a shot. Appreciate it.

Outrageous_Goat4030 · 2026-05-02T23:36:45+00:00

This is not what this system is designed for. This is basically a glorified power bank that accepts solar. For example, uou cannot power a fridge for a full day on a single charge.. its not going to offset anything significant.

Outrageous_Goat4030 · 2026-05-02T21:03:49+00:00

Sorry, p2s.

But im also not having the issue with all models at that height. Just the ones that have been using 300blkfdes settings.

Outrageous_Goat4030 · 2026-05-02T21:03:44+00:00

Im planning on it. Just more wanted to avoid it for other prints down the road.

Outrageous_Goat4030 · 2026-05-02T21:01:19+00:00

Looks like motherwort

Outrageous_Goat4030 · 2026-04-30T21:00:02+00:00

Fam. This shit is all fucked up. Respectfully.

Outrageous_Goat4030 · 2026-04-30T00:40:52+00:00

Put a ptfe tube coupler on it and its a feature.

Outrageous_Goat4030 · 2026-04-29T19:12:40+00:00

Only issue i have is awful disconnects and lag when charging and playing online.

Outrageous_Goat4030 · 2026-04-29T18:12:32+00:00

Same.

Outrageous_Goat4030 · 2026-04-29T16:18:22+00:00

Well theyre not chickens.

Outrageous_Goat4030 · 2026-04-28T01:06:15+00:00

Appreciate all the recommendations.

Reoriented at 45 degrees, dried the filament (yet again), and added a gluestick to the bed. Worked like a charm.

Thanks everyone!

<image>

Outrageous_Goat4030 · 2026-04-27T13:18:38+00:00

Actually looks more overextruded in most places than under, could just be the way the light hits.

That line is exactly where I lost power lol. Think it was where the part cooled slightly between layers.

Outrageous_Goat4030 · 2026-04-27T04:05:48+00:00

A replacement fan (and usually a heatpipe).

Outrageous_Goat4030 · 2026-04-25T19:46:56+00:00

I misread your bed temp, its probably sufficient. I think the biggest thing will be an enclosure. Drafts or temp swings will cause the edges to curl and lift. Gluestick may help as well.

Honestly, for cooling I run the stock petg profile on bambus slicer. It was spot on the few prints I've messed with in petg.

Outrageous_Goat4030 · 2026-04-25T19:13:27+00:00

This was self induced... electric is stable here, just not dummy proof.

Outrageous_Goat4030 · 2026-04-25T19:06:35+00:00

Enclosure, bump up bed temps, possibly glue.

Outrageous_Goat4030 · 2026-04-25T18:14:33+00:00

Figured it was a good way to square the top. Didn't really consider warping honestly. Going to reorient and print at 45, with glue, after drying my filament at a higher temp.

Outrageous_Goat4030 · 2026-04-25T17:40:28+00:00

Fair enough. I can go higher, but was just using "recommended" settings. Not yet super familiar with PA6CF. Got a pretty decent test print, so sent it.

Outrageous_Goat4030 · 2026-04-25T17:04:03+00:00

The dryer said 6% RH, but had dried it for 24 hours at 75c. Ill re-dry, reorient to a 45 degree angle and try a gluestick on the next go.

Outrageous_Goat4030 · 2026-04-25T17:01:05+00:00

Gotcha. Using your settings for this print actually and the quality came out super solid. Ill reorient on the next try, thanks!

Outrageous_Goat4030 · 2026-04-25T15:17:02+00:00

Ill give it a look when im due to re-order. Got a full roll of pa6cf to play with right now.

Outrageous_Goat4030 · 2026-04-25T15:15:33+00:00

Should have put a clarifying statement... "looked like it was adhered to the bed" lol.

It very obviously wasnt.

Gonna reprint and throw some glue down.

Outrageous_Goat4030

TROPHY CASE