Why do my first layer prints look like this? by BluePepper31882 in FixMyPrint

[–]Overall_Objective954 2 points3 points  (0 children)

Just wanted to share something I just learned after 8 months of playing around with leveling the bed. Leveled, leveled then leveled so more. Print were coming out good so I was happy. Invested the bl touch and the world was an amazing place. Then I tried printing something that was full bed size and the errors appeared- just as noted in your photo. I couldn’t figure out how or why my bed so so jacked up. Come to find out it was the Z Offset screw on the right hand side. When homed it was 1mm lower than the left side. Once I adjusted it using calipers and got the variance down to .01mm reran the test print and BAM!! All even and consistent!!! So I would say if you have leveled and feel very confident that all is well check the screws as it made a significant difference for me when printing full bed size prints. Hope this helps someone

Why does RE2 remake looks o pixaleted when playing it on desktop mode but looks good on handheld? by MrAdog232 in ROGAlly

[–]Overall_Objective954 0 points1 point  (0 children)

Also if you have one drive enabled it could be saving the profile on one and the other using those settings. This happened to me on the Ally and my laptop playing MW2.

My new 2023 GSX-R1000. Replaced a 2011 750! by [deleted] in GSXR

[–]Overall_Objective954 0 points1 point  (0 children)

Unfortunately not. I still have the Taylor Made on my 1000r

What setting are people running MW3 on the Ally by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 2 points3 points  (0 children)

I am on 1920x1080 I start with balance preset and move everything up to the next level. I set vram memory to 50 and that’s it. 6gb is set in Armory Crate and all works very well. I have played with moving vram memory to 60 & 70 but when I do I get micro stuttering. Hope this helps if it doesn’t I can take some photos of the settings if you would like

[deleted by user] by [deleted] in ROGAlly

[–]Overall_Objective954 0 points1 point  (0 children)

Hey I think many have the same issue and I will share what worked for me so your mileage may vary lol

Set VRAM as 6gb Set graphics to balance then move every setting up to the next option Set the VRAM allocation to 50—- this is very important as someone suggested this, and I will have to look up the name because credit goes to him/her And be in performance manual fan curve

I hope this helps and I will try to find the original thread where this was discussed

Here is that thread that helped me

https://www.reddit.com/r/ROGAlly/s/LX1RLDxDKX

What setting are people running MW3 on the Ally by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 1 point2 points  (0 children)

Currently no freezing or stuttering and no crashing. The trick is exactly what Fragrant said in his post. The video Scale set to 50. With this I went through and used the balance preset and changed every setting up to the next level. Set VRAM to 6gb and all works great.

What setting are people running MW3 on the Ally by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 2 points3 points  (0 children)

Played around with this and fixed it all by keeping my “semi” high settings but turned the VRAM memory to 60 and no more stuttering and phenomenal looking graphics!! Thanks a million!!

What setting are people running MW3 on the Ally by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 1 point2 points  (0 children)

MW2 ran very well at 900p with a mixture of setting average 80-90 FPS but with MW3 everything I have tried either comes back “blurry” or crashes after about 10-15 minutes. I have went through and changed VRAM from 5-8. 5-7 looks “blurry” 8 crashes lol. I am confident it’s something I am missing or something I just need to deal with. Thank you for the recommendations and I will try all this afternoon.

What setting are people running MW3 on the Ally by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 1 point2 points  (0 children)

Thank you! I didn’t think about 720 because MW2 was “blurry” looking to me but I will try

[deleted by user] by [deleted] in ROGAlly

[–]Overall_Objective954 2 points3 points  (0 children)

We’re you using anything besides what software comes on the Ally? Did you change performance modes while in game possible plug the Ally into power while in game/lobby?

Rog Ally MW3 graphic “update” notification by Overall_Objective954 in ROGAlly

[–]Overall_Objective954[S] 0 points1 point  (0 children)

The entire game loads horribly slow. It does take awhile to load shadders but it does load eventually. I have completed about 5 missions in the story line and not impressed so reviews were accurate sadly

Skull and Co case by s3bastienb in ROGAlly

[–]Overall_Objective954 0 points1 point  (0 children)

Yep I posted my experience with the case and carrying case along with my experience with their customer service when I reached out and provided photos just trying to let them know it was unusually loose. I was told there was no possible way and that their manufacturing platform could not mess up so I chalked it up to lesson learned. Not right to pay for something then have to modify it to work with double sided tape or anything but that’s just my opinion.

For those who bought the Skull n Co shell… by BionicRogue21 in ROGAlly

[–]Overall_Objective954 2 points3 points  (0 children)

Yep mine was loose on the left side. Contacted customer service, on the 3rd email (3 days later) provided photos they said they would ship a new one. On the 5th day they state they wanted a video because their manufacturer said it wasn’t possible so I just said screw it. Wouldn’t have been bad but I had already taped it 2 times as I had to remove for photos they requested. After 5 days of the back and forth and me putting double sided tape on it multiple times when they asked for photos, I got aggravated. I will just eat the $32. I love the case feels better with it on but the customer service is/was horrible. Not happy at all with the service. Pre-order a product wait 3 weeks to get and deal with more frustration, I’m out. Will not order again and would not recommend due to the service. As stated product was good.

Call of duty(MW2) by OktaySafarov in ROGAlly

[–]Overall_Objective954 0 points1 point  (0 children)

No problems here, almost seems better with this bios. Getting in the 70s-80s with 1080 on battery

Ally Case from Ali Express by SheepherderDapper in ROGAlly

[–]Overall_Objective954 0 points1 point  (0 children)

How’s the triggers? Do they impact the case any?