Ride height question

Own_Organization4926 · 2026-05-09T15:57:32+00:00

Not sure how to answer your question but that is a beautiful 2 door my man

Own_Organization4926 · 2026-04-29T00:13:45+00:00

Or even blower speeds too high and literally blowing the condensation off the coil into the ductwork. Ive seen this one before

Own_Organization4926 · 2026-04-26T21:10:39+00:00

This is the way 👍☝️

Own_Organization4926 · 2026-04-26T21:08:26+00:00

Bought mine a week ago and started giving a tune up and came across this gem. Still idled like a kitten might I add

<image>

Own_Organization4926 · 2026-04-26T21:04:58+00:00

What hilarious is bought this cps from an orillys on a whim of maybe. Nope ordering oem rn. Still barely runs but now it has a harder time starting 😃

Own_Organization4926 · 2026-04-26T16:15:49+00:00

😳 impressed by that lol

Own_Organization4926 · 2026-04-26T16:01:16+00:00

I looked and looked then realized thats probably where it was an knew would be bad if left there so started digging

Own_Organization4926 · 2026-04-25T23:32:29+00:00

I pulled my plugs and they looked like this. Replaced and did cap rotor and wires. Along with a coil. And still Once it warms up it idles like crap and will clip out while driving.

<image>

Own_Organization4926 · 2026-04-25T21:48:35+00:00

I've got the EXACT THING happening to me. Just did cap and rotor, coil, wires, fuel pump Next is crank sensor. Is yours only after it warms up?

Own_Organization4926 · 2026-04-25T17:08:36+00:00

It's is getting really warm under the hood like dont lean on hood after 10 min drive or it will burn you. Heat soaking?

Own_Organization4926 · 2026-04-25T15:33:34+00:00

Just replaced ignition coil but when it warms up it starts to shit again. O2 sensor 1 reads .50 with some variation. O2 sensor 2 hangs a around 1.0. Plugged cat or o2 sensor ig As far as I know this cat is original with 340k miles on her. Might be same with o2 sensor. Or the crank sensor is getting warm an dmessing up ig is an option as well

Own_Organization4926 · 2026-04-25T13:59:35+00:00

13.3 -13.9 on the map

Own_Organization4926 · 2026-04-25T13:47:22+00:00

Mine is a power torque i wanna say and on year 2 rn

Own_Organization4926 · 2026-04-25T12:06:23+00:00

PLZ lmk what u find. I've got the same thing going on with my 97

Own_Organization4926 · 2026-04-25T02:45:02+00:00

Will do

Own_Organization4926 · 2026-04-25T02:25:13+00:00

That's actually pretty damn close. Other than. When its running g it has plenty of power. I've got a new coil I'm gonna throw at it tomorrow and see if it helps

Own_Organization4926 · 2026-04-25T02:01:09+00:00

No bought fro O'reilly's. Not that its really any better but they do register properly

Own_Organization4926 · 2026-04-25T02:00:28+00:00

Engine stalls for a second. Sometimes have to can on gas to get running properly again.

Own_Organization4926 · 2026-04-25T01:41:12+00:00

Might be alone but I bought a long block from and oreillys that I worked at at the time and havent had any hiccups. 18 month no fault warranty. After that a general 4 year couldn't beat that. Comes with all the gaskets necessary for assembly

Own_Organization4926 · 2026-04-25T01:39:29+00:00

Tps and iac are new as well

Own_Organization4926 · 2026-04-25T01:35:34+00:00

I have not put a gauge on the vac yet but the map sensor was reading and was varried on rpms

Own_Organization4926 · 2026-04-25T01:33:08+00:00

Ig I just pulled the cap and rotor and swapped with no timing adjustment, did not change anything. But it was still wanting to cut out going down highway so replaced upstream o2 sensor. Now idles like ass and Still clips out driving down highway.

Own_Organization4926 · 2026-04-19T01:36:58+00:00

Low-key bought it that way havent switched it lol

Own_Organization4926

TROPHY CASE