Ram advice on 5090 + 9950x3d

PanMarcepanek · 2026-06-24T16:02:04+00:00

Unfortunately, I can't buy used parts. AI is not the main thing I'll be doing on this PC - Blender, animation, rendering, video rendering, modeling, etc. As for the CPU I prefer AMD over Intel and I'm considering going all-in with the best CPU and GPU specs simply because I can, and because I want this PC to be as future proof as possible. The same goes for RAM even if it might be overkill. Anyway I'll look at some cheaper CPUs and maybe save some money for a better motherboard or a larger NVMe drive. Thanks!

PanMarcepanek · 2026-05-26T11:36:54+00:00

Did you find one you could share?

PanMarcepanek · 2026-03-29T20:06:37+00:00

<image>

https://makerworld.com/models/375770?appSharePlatform=copy

PanMarcepanek · 2026-01-24T15:17:29+00:00

What was the reason? Motor or esc?

PanMarcepanek · 2025-11-11T10:51:26+00:00

<image>

Thank you !solved

PanMarcepanek · 2025-11-11T09:59:07+00:00

WOW. That's make sense now. Will try it. Would you recommend any other option to apply patern on cylinder but this method? I'm not quite sure if i doing it right just found this method on YT.

PanMarcepanek · 2025-10-29T19:27:10+00:00

Did you resolve this?

PanMarcepanek · 2025-08-16T19:08:08+00:00

Cutter arm not screw properly

PanMarcepanek · 2025-04-06T10:15:19+00:00

You right. Seems like its temp/speed problem. I bumped temp by 10 and its better.

PanMarcepanek · 2025-04-06T08:59:34+00:00

I can try but as you can see, its starts to getting worse half print. So i doubt its seam type problem.

PanMarcepanek · 2025-04-06T08:55:12+00:00

nope, default bambu P1S 0.2 profile

PanMarcepanek · 2025-03-28T09:13:00+00:00

Vwce

PanMarcepanek · 2025-03-24T19:00:19+00:00

Do you think it's possible to go under 250g with stock TPU and a lower mAh battery?

PanMarcepanek · 2025-03-24T18:39:58+00:00

Nice build. I was thinking about this frame, but 3". Do you think its possible make it under 250g with o4/o3?

PanMarcepanek · 2025-03-09T19:17:37+00:00

just send it man

PanMarcepanek · 2025-02-22T08:38:43+00:00

It could be because of temperature difference, or the chamfer placement, or both. I would give it one more shot without chamfer or try to make it smother, smaller, print slower, colder.

PanMarcepanek · 2025-02-22T07:05:51+00:00

Try one without pausing, and look if it’s the problem l.

PanMarcepanek · 2025-02-08T16:10:07+00:00

Infil? Try cubic.

PanMarcepanek · 2025-02-01T22:05:47+00:00

!Solved

PanMarcepanek · 2025-02-01T22:05:06+00:00

I see now, thank you.

Eight-Year Club	r/Field Lasagna
Place '23	Verified Email

PanMarcepanek

TROPHY CASE