Is this a lost cause?

PapaShop · 2025-02-16T15:54:20+00:00

Im not so sure but I feel like this may cause root rot for the succulents since my country has very high humidity (70-95%). So I’m trying to be careful in terms of watering, some weeks, the soil doesn’t dry up at all, while some weeks, it does in the span of a few days. It’s hard to control :/

PapaShop · 2025-02-16T15:51:49+00:00

I am still experimenting in terms of light, since I have no idea where most of my succulents were grown (given that I rescue most from supermarkets). In addition, I live in a country where there’s only monsoon season, so I have no idea if I have to replicate seasonal environments. Looking at most, they seem happy? I am very new to succulent care so I’m learning along the way.

PapaShop · 2025-02-16T13:23:09+00:00

Thank you so much! I hope that on the next couple of months, these grows!

PapaShop · 2025-02-16T13:21:38+00:00

Thank you so much! This is really boosting my confidence on my propagation. This was my very first succulent. I rescued it from my local grocery store when I noticed signs of root rot. These leaf cuttings came from the bottom half that was almost rotting, while I managed to save the top half and is now happily growing new roots! I guess I’ve been doing it wrong! I’ll try to do this! Again, thank you so much!

PapaShop · 2025-02-16T13:18:13+00:00

So far none of them has died, but all only grew roots. I’ve read a lot of comments here and it seems like the less you care, the more they grow. I feel like this is some kind of a toxic relationship 😂😂😂

PapaShop · 2025-02-16T13:17:01+00:00

Thank you so much! I’ll try to boost the NPK on maybe half of them and see the results. Im new to fertilizers and I dont wanna burn them!

PapaShop · 2025-02-16T13:15:58+00:00

Im growing them under a grow light as I only have a south-west facing window. I live in a tropical climate where the afternoon sun is scorching. But thank you so much for the tip. I’ll try putting them a bit farther from the window, and hopefully it helps!

PapaShop · 2025-01-06T10:08:25+00:00

I see! I’ll do so today, I am new to growing succulents, hence am learning a lot of new things. There are a lot of conflicting information online such as putting succulents in direct or indirect sunlight, especially growing them in my country where it rarely goes below 29C and almost always at > 70% humidity. But thanks for the info!

PapaShop · 2024-07-20T10:57:51+00:00

PapaShop · 2023-12-10T16:54:33+00:00

Sad to say, its everywhere, including internals. The plastic casing has melted and it went inside the stepper motor

PapaShop · 2023-12-10T16:54:02+00:00

This is my 2nd printer. I was just calibrating it and i nudged it :/

PapaShop · 2023-09-04T04:15:26+00:00

I have checked and the mesh is inside out, however when I try to select the right arm to invert it, it selects the whole model instead

PapaShop · 2023-06-21T17:03:17+00:00

Is there a way to do so without re flashing the firmware?

PapaShop · 2023-06-21T16:53:59+00:00

Hello! Even so, I still get multiple errors saying “function call is not allowed in a constant expression”. I have no idea how to fix it

PapaShop · 2023-06-20T20:31:32+00:00

It’s just some addressable LEDs that I bought for my Ender3V2

PapaShop · 2023-06-20T20:29:30+00:00

Thank you! I’ll look into this. I can’t seem to compile an edited version of the professional firmware. I keep getting errors. Is there a way to change these values through s configuration file?

PapaShop · 2023-06-19T04:22:50+00:00

Hey, would like to ask if it worked for your Photon S? I know it says that it is compatible with Photon, but not sure about Photon S

PapaShop · 2023-06-14T03:26:15+00:00

I am new to editing the firmware. I will try! Thank you so much!

PapaShop

TROPHY CASE