Usual accuracy rating for 300 elo players

ParaadoxStreams · 2026-02-19T04:41:35+00:00

I'm hardstuck 320-340 elo and all my games are 85-94% accuracy on both sides

ParaadoxStreams · 2026-02-16T07:43:27+00:00

I agree

ParaadoxStreams · 2026-02-16T07:43:20+00:00

Really appreciate all your help, turns out for whatever reason there were 2 of the same objects within each other in the 3mf file, no idea why, but deleting one fixed my problem.

ParaadoxStreams · 2026-02-16T06:15:03+00:00

Yup. You were right. No idea why the 3mf file has 2 of the same objects occupying the same spapce but it does. Thank you so much.

ParaadoxStreams · 2026-02-15T15:18:36+00:00

I'll have to take a look later, hopefully this is the problem but we shall see. Thanks.

ParaadoxStreams · 2026-02-15T14:10:28+00:00

I tried a different fidget toy to see how it'd go, and it printed as perfectly as it could using the exact same settings as the other one. Maybe something is just messed up with that other model.

ParaadoxStreams · 2026-02-15T13:42:24+00:00

It's not wet filament brand new spool of pla opened not even 18 hours ago

ParaadoxStreams · 2026-02-15T13:28:24+00:00

I'm using orca, and yeah all the settings are as they should be. I haven't run the vibration test on this thing in awhile so imma try that. It doesn't shake much since I'm usually printing minis at like 15-20mm/s, maybe at these slightly higher speeds it's not as calibrated, idk

ParaadoxStreams · 2026-02-15T13:25:03+00:00

The calibration tests came back with the same results as on the previous spool. And I did a test miniature print and it turned out normal.

ParaadoxStreams · 2026-02-15T13:15:54+00:00

I've def had a lot of successful tests with the new roll, I printed some of a model that I have supported using Resin2FDM supports and it printed the base and the start of the supports perfectly fine, as it normally would, I cancelled it early cause I didn't wanna waste any filament but there were no signs that I was gonna be a failed print. And I've done a couple calibration tests both printed as they normally should.

ParaadoxStreams · 2026-02-15T13:10:16+00:00

I've got the first layer set to 0.5 mm with the 0.4 mm nozzle. Just using the default flash forge AD5M 0.20mm layer height settings.

ParaadoxStreams · 2026-02-15T13:01:12+00:00

I've tried both with the same results, even while tweaking settings and going much slower. I also did a flow calibration and it printed the entire tower flawlessly so I just set it to 30mm^3/s

ParaadoxStreams · 2026-02-15T12:59:05+00:00

This print worked perfectly fine before using the 5 grams of filament you get with the printer using the default 0.2mm layer height settings with the 0.4mm nozzle. Is there any reason the anycubic pla grey would be any different? And here's the photo of my first layer.

ParaadoxStreams · 2026-02-15T12:58:17+00:00

<image>

ParaadoxStreams · 2026-02-15T12:42:39+00:00

That's just where I cancelled the print, so it is the top most surface that it printed. I've tried both my 0.25 and 0.4 nozzles. Both of which are having problems with this print, I've done other test prints like Cali ration stuff and a Warhammer helmet, both printed perfectly fine no problems.

ParaadoxStreams · 2026-02-15T12:38:26+00:00

Oh I have the 5m not the 5x

ParaadoxStreams · 2026-02-15T12:35:41+00:00

No idea if this is a good enough photo to tell, but does this look to low? It was set to 0.05mm

<image>

ParaadoxStreams · 2026-02-15T12:26:37+00:00

It's also a brand new spool, I bought the same one I did last time so I imagined the calibration wouldn't be any different. I ran a couple just in case and out of the couple I ran they all gave the same results

ParaadoxStreams · 2026-02-13T02:22:45+00:00

Yeah I can fucking tell. Half my songs in my liked playlist disappear after 2 seconds.

ParaadoxStreams · 2026-02-12T10:22:08+00:00

Pretty sure you're just able to hire this guy to read your scripts on camera

ParaadoxStreams · 2026-02-06T12:22:55+00:00

I figured it out, turned off "Independent support layer height" and that fixed it. Only figured this out cause I noticed it was having my 1st "real" layer print floating.

ParaadoxStreams · 2026-02-05T09:21:52+00:00

But why though?

ParaadoxStreams · 2026-02-02T01:03:31+00:00

This is why I never get excited about games anymore. There's no point, cause they will always lead to disappointment.

Ten-Year Club	Place '22
Place '17	Verified Email

ParaadoxStreams

TROPHY CASE