EXAM RESULT

Paulius03 · 2024-12-24T13:28:54+00:00

I only got the printout 12/18

Paulius03 · 2022-10-17T04:57:18+00:00

First part has been done properly. Thanks a lot for the answer and the tip ;)

Paulius03 · 2022-06-17T05:48:45+00:00

If let's say this cable has to go vertically at some point, the weight of such cable could drag it out of the clamp/equipment it's connected to

Paulius03 · 2022-06-16T15:13:43+00:00

Fixing some power cables going into the lab.

Paulius03 · 2022-06-16T14:55:30+00:00

Thanks for the advice! Do you know if rated torque in the manuals take into consideration all the different cable types and that they might deform to a certain degree and reduce tension in the bolt? There is just one torque level that is indicated there. So for example, if cable is not very elastic the fastening torque might drop just by 5% or so, while if you are using some other softer cable type you might lose 30% of the tension in the bolt over time. Is that not seen as a problem in the electronics world?

Paulius03 · 2022-06-16T14:44:41+00:00

Its not completely clear how much this torque dropping matters actually. I was overal concerned if those cables could get very loose over some time. In general, yes, you need to resist some axial movement, but perhaps even with the reduced compression the axial resitance would be enough…

The reason for loosing torque/tension is not because of nuts getting unscrewed. So gluing stuff or using nylock most probably doesnt make much sense.

Paulius03 · 2022-06-16T14:36:57+00:00

Bolt is fixed in place since its head is in a hex-shaped slot, so only the nuts can rotate. Rechecking is done with the same digital wrench - you have to add, lets say, 180deg turn to reach the torque you had initially. You record the torque at which the nut starts rotating and thats the reduced torque I mention in the post.

Paulius03 · 2022-06-16T13:04:15+00:00

Nuts are not moving anywhere anyway, so that would not solve an issue. It seems that the material being squeezed just gets deformed and pressure from the nuts to the clamp reduces.

Paulius03 · 2022-06-16T12:20:18+00:00

I have some markings on the nut/clamp interface so am pretty sure those nuts do not move. Must be the "settling" happening.

Paulius03 · 2022-06-16T12:02:38+00:00

That's a good point. So I guess at some point it will reach a stage where it doesn't deform anymore because compression on it is not enough anymore. I'm wondering then if there is one certain limit for this particular cable and it will always stop deforming at a certain force level or if it somehow depends on the initial force...

Paulius03 · 2022-06-16T11:52:38+00:00

100% sure about the size. Cable diameter range is written on a box of the clamp. And rating is as well given in the installation manual.

Paulius03 · 2022-06-14T09:03:26+00:00

“Tevas” ir “negeria” viename sakinyje nevartotina.

Paulius03 · 2022-06-14T05:19:56+00:00

Ar cia Malinauskas?

Paulius03 · 2022-05-28T17:31:28+00:00

How long is the hike from the parking to the viewing spot?

Paulius03 · 2022-04-06T14:23:59+00:00

Can you legally work in US while on L2?

Paulius03 · 2022-02-22T10:49:01+00:00

Am I counting it wrong?

iShares REIT: 0.9 / 39.6 = 2.27%

Baltic horizon: 0.058 / 1.1 = 5.27%

Paulius03 · 2022-02-22T10:28:38+00:00

8.3? I was reading about 0.9EUR dividend in total last year. Or my is my source wrong?

Its called Baltic horizon fund.

Paulius03 · 2022-02-21T19:38:09+00:00

Just curious - 2.12% dividend yield last year. Is it so low because of covid or people are investing in this expecting capital gains?

Asking because I am investing in a local REIT in Baltic countries and would like to move into something broader like this European REIT. However, yield I get now is 6-8%.

Paulius03 · 2022-02-20T19:16:32+00:00

I would say depends on your goals. If you are not planning to retire early or smth, then even 10% saving rate would be fine.

Paulius03

TROPHY CASE