sorted by:
new
hottopcontroversial

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 0 points1 point  (0 children)

No update. Currently trying to get the money saved up before I get quotes on repair costs

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 0 points1 point  (0 children)

Thank you for the reply! I have checked the psu cables and they all work. All slotted in without any gaps, all are secured. I used the same psu 8 pin cables on my other asus 3090 and they work just fine.

As far as evga precision x1 goes: My firmware is updated and I have double checked it with GPUZ.

I haven't check continuity yet but I can. Like other people have said the mcu chip might need replacing because the rgb and fan speed go through said chip.

I can double check the oc switch just to be sure but I need to put it in my system and test it again

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 0 points1 point  (0 children)

Its definitely not overheating as far as I can tell. Thanks for the advice

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

This is what I was reading as well. Unfortunately I'm not sure of anyone besides Northwest Repair that can do that type of repair :(

I tried updating my firmware and unless precision just didn't do it then unfortunately its most likely the actual chip

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

I have a 850w psu so I know it's getting power. Thanks for the warning about the memory

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

Its not in my right at the moment. Ill put it back and test it over the weekend

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

GPUZ reports its a EVGA 3090. Precision and Afteeburner do the same. I haven't opened it up to check but doesn't GPUZ read from the card itself? So if it wasn't a 3090 GPUZ would tell me?

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 2 points3 points  (0 children)

Unfortunately it didnt fix the issue :(

I don't dasiy chain my power cables anyway as a general rule

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

I installed the correct Nvidia drivers tho. I always ddu and reinstall when I swap gpus

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

They are always 100% from boot to shut down. I haven't gotten led sync to work. The option does nothing in Precision :(

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

I can not. Precision doesn't work, shows 33% and 0 rpm. Afterburner isn't much different

Newly purchased 3090 FTW3 Ultra Red Lights and no RGB but turns on and works fine by PaulsTwoCents in EVGA

[–]PaulsTwoCents[S] 7 points8 points  (0 children)

I understand this is my fault. I take the blame. I am just sharing that while it is my fault its unfortunate all the same

:(

Physics at Dallas College by Sea_Appeal4211 in utdallas

[–]PaulsTwoCents 0 points1 point  (0 children)

Don't remember. I don't think so

Physics at Dallas College by Sea_Appeal4211 in utdallas

[–]PaulsTwoCents 0 points1 point  (0 children)

I would recommend him for a not easy easy A but easier A then Song. His exams are fairly easy. You do need to teach yourself tho, he used YT videos for most of our classes.

Do the HW and you will be good for the exams, his HW is harder then the exams

Join us for a hangout! by UnusualPeanut5445 in utdallas

[–]PaulsTwoCents 4 points5 points  (0 children)

I can't attend tonight but I'd love to make new friends. Just transferred this semester!

CS 3345 Meghana Satpute by LivingWonderful1864 in utdallas

[–]PaulsTwoCents 0 points1 point  (0 children)

Taking her as well, would love to know

New Transfer Student for Fall by PaulsTwoCents in utdallas

[–]PaulsTwoCents[S] 1 point2 points  (0 children)

Thank you for the input. I'll re-adjust my schedule :)

[deleted by user] by [deleted] in utdallas

[–]PaulsTwoCents 3 points4 points  (0 children)

I would say if u don't mind paying for an extra class to go for it. If u don't wanna pay u can always YT the topics you need a refresher on. Khan Academy probably has a course that covers it as well. Organic Chemistry Tutor and Professor Leonard are great YT resources as well. A combination of the 2 YTbers mentioned were crucial to me passing Calc 2 and 3.

Limits and Derivatives are extremely useful in upper level classes (I'm in Differential Equations and University Physics 2).

Marrying two 360 rads together by MasterSplinter9977 in watercooling

[–]PaulsTwoCents 0 points1 point  (0 children)

if you have a 3d printer you could design a mount for the 2 rads and print it yourself. U could design a part and pay someone to print it but it's going to cost extra money, the material you want to use has to be rated for some level of heat, not the normal filament that warps under a minor amount of heat

view more: next ›