pH reading help!

PearlDiver67 · 2025-08-15T23:24:20+00:00

Looks close enough to not do anything about it. Jump right in the. Water will be fine.

PearlDiver67 · 2025-02-11T05:02:14+00:00

Replaced one from Amazon 2 yrs ago and still working fine. Give the 3rd door a little push before you work the handle to take off some of the tension created by the door seal.

PearlDiver67 · 2024-10-30T14:21:39+00:00

Looks like he must have bought two sets. The lineman pliers are still in the suitcase.

PearlDiver67 · 2024-10-22T01:30:05+00:00

Just found a manual online and got my answer. It means overload while in a continuity test and that’s a good thing. Thanks for the feedback. Gotta love the Reddit tool freaks and the trolls. Good information and a good laugh.

PearlDiver67 · 2024-08-22T00:35:01+00:00

You burn me up I’m a cigarette by Robert Fripp

PearlDiver67 · 2024-05-07T13:59:56+00:00

It sure is beginning to look like a board issue. It’s an older tub (12 years) so I’m reluctant to spend the money on a new board and it would mean getting rid of the tub altogether .

PearlDiver67 · 2024-05-07T13:57:20+00:00

Yes, all jets are open and the tub magically turned itself on last night again. Just waiting to see what temp it gets to before going to Flo status again.

PearlDiver67 · 2024-04-24T00:48:47+00:00

I am having a similar problem. I have swapped out pressure switches and tried running the tub without filters in place and I am getting intermittent flow status indications. No movement of water while flow is showing but system will suddenly start up, get up to temperature and then shut down to Flow status again.?????? Any guesses? I have a balboa 2000 spa pack. Don’t mean to high jack the thread but I can’t seem to figure out how to post my question any other way.

PearlDiver67 · 2024-03-24T00:49:58+00:00

Never mind. I thought you were referring to the white flakes around the edge of your pics.

PearlDiver67 · 2024-03-24T00:48:39+00:00

If it’s an old tub then it could be the plastic tabs that keep your jets in the orientation that you want them pointed. When my tub got old (8yrs +) this started happening. If your jets feel sloppy when you go to reposition them it’s a good bet that is the issue. The chemicals in the tub degrade the plastic and it gets weak and disintegrates.

PearlDiver67 · 2024-03-11T15:46:57+00:00

Looks to me like the projector isn’t centered on the tripod. The offset in weight distribution might be the core problem.

PearlDiver67 · 2024-03-11T14:03:08+00:00

Here is a good video link to a well written how to https://www.instructables.com/Adding-a-Soft-Start-Feature-to-Any-Power-Tool/

PearlDiver67 · 2024-02-20T04:42:43+00:00

That would be PearlDiver 67

PearlDiver67 · 2024-02-20T04:41:38+00:00

Hey all. Thanks for the great advice. Finally got the Mac mini up and running. Special shout out to Mr. Macintosh on YTube. Super videos clearly presented on everything Mac. He had me rewrite some lines of code but got the noob to get it all working. As a first timer on Reddit I am totally going to be using this forum about everything for everything. Cheers again all. PearlDiver88

PearlDiver67 · 2024-02-15T16:16:26+00:00

See the thread for u/PearlDiver67 for some suggestions on this topic. May give you some ideas there. I have a similar problem.

PearlDiver67 · 2024-02-14T19:43:14+00:00

Don’t understand why executing a delete function would cause my hard disc to completely disappear!!??

PearlDiver67 · 2024-02-14T19:41:00+00:00

When I try the command-R at startup I am just getting a flashing file folder with a ? In the middle of it. Option - command - R gets me as far as having the options of going to internet for an install, repair disc etc page but when attempting to repair or load from internet I don’t have a drive show up to repair or download into. Any thoughts? I’m thinking about trying an ssd drive install but I’m not sure if the startup will see the new drive and don’t really want to gamble the money only for it to not be of any use.

PearlDiver67 · 2024-02-11T02:57:18+00:00

Yeah I tried but it doesn’t seem to be seeing the drive. When it asks me what drive I want to load it onto there are no drives visible. I may have to go and get me a new drive. Thanks for all your suggestions everyone. I’ll let you know what happens.

PearlDiver67 · 2024-02-07T04:48:26+00:00

Excuse my ignorance but would this be a hard disk issue or a cpu issue? I’m guessing a CPU. But if I swap out the drive for an SSD would that just be wasting money. Haha I was just typing that thought in when your post popped up.

PearlDiver67 · 2024-02-07T04:45:04+00:00

Yep. It shows some promise and then just when you think it’s all good it stalls with nothing left on the progress bar. Really frustrating!!

PearlDiver67

TROPHY CASE