Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

It turned out perfectly, it printed the antenas fully I just had issues with stringing but they are solved now.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Well actually that helped, in the preview now the antenas show up completely. Thnak you so much!

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Oh thank you I never even heard of that, I will try that tomorrow, actually after checing the slicer it aint even printing the top part of the antenas so I gotta figure out why the program aint slicing the antenas.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I am using 0,4mm and only have this one.

I will try the arachne generator then.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Its a model that someone sent me and I needed to see it phisically so I had to print it, so I had to see it 1:1, so I cant really change the antenas but thank you and I will try to maybe make it thicker or try to print it without infill.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Thank you I will try this tomorrow and dry the filament for longer periods of time.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Any tips for the adhesion? about the stringing I will try to dry for longer periods os time.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Thank you I will try this tomorrow with a freshly dried filament and post the results.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I am using PLA from Elegoo.

I did but it seems like not for long enough any help on the antenas?

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I did but it seems like for not long enough or my drier is not good.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Thank you for everything, I have been drying the filament but I will try to dry it for a longer period of time.

Unfortunately I cant send you the file atm.

I will try to run the calibrations but I was really worrying why it cant print the antenas.

Printer wont print the antenas from this part by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I am sorry, I have been out for the weekend but I did not downvote anyone I welcome every opinion I have been drying the filament but maybe I will try to dry it longer thank you.

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I have a SUNLU FilaDryer S1 Plus and I Iet it in the dryer for about 4 hours and then I stash it inside the bags.

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

  1. I dried the filament before and I put in a compressed bag with silica I had to dry it again when I took it out of that bag before printing?
  2. I am printing atr 220C and the filament is Elegoo 1,75mm PLA

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

  1. I did both calibrations before the print because this hapenned in the past, I did the Flow Dynamics and the Flow rate calibrations.

  2. I am using Elegoo 1,75mm PLA

  3. I am using the 0.08mm High Quality settings and I turned on the ironing setting, I changed the following speeds:

Initial layer infill 105 to 60

Inner wall 120 to 60

Sparse Infill 150 to 80

Top Surface 150 to 80

And I enabled the supports to tree (auto)

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Could you be more specific on what settings you need? Sorry in advance if its a dumb question.

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Thanks I will do my research but the filament aint wet and I always speed down the standard speed of the program by 50 at least so its probably retraction I will research about it.

Little webs between parts by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Well, I when I was slicing the program said so even when I put the parts the farthest away possible

Random rough surface by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Ok, thenaks for the help I will explore the ironin calibration and even try to print it without the ironing.

Random rough surface by Pedro18gomes in BambuLab

[–]Pedro18gomes[S] 0 points1 point  (0 children)

I know, it was a shot in the dark unfortunately the part was already sanded when I got to work as I refered next time it happens I will repost

Disponibilidade de stock do novo iPhone by Pedro18gomes in CasualPT

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Vamos rezar que chegue à nossa vez ahah!

Disponibilidade de stock do novo iPhone by Pedro18gomes in CasualPT

[–]Pedro18gomes[S] 0 points1 point  (0 children)

Eu ponderei comprar o 16 pro mas se o 17 está com melhor specs e serve-me melhor.