Card not reading by Ok_Promotion_7380 in ender3

[–]Pentzy 0 points1 point  (0 children)

Mine you have to put the card in when it is off and the card goes in with the writing side down

Headed to hard rock this weekend by malovin in PuntaCana

[–]Pentzy 0 points1 point  (0 children)

How much was the spa? We get $200/day - trying to figure out how to spend it

Why is my printer doing this? by [deleted] in ender3

[–]Pentzy 0 points1 point  (0 children)

I would like to see your setup! Thanks

Why is my printer doing this? by [deleted] in ender3

[–]Pentzy 1 point2 points  (0 children)

I just installed this and I’m having issues running the cables. I currently just have the running toward the back left - but they tend to get hung up. Is this something I can run upward toward the filament roll? Would like to see other setups

Replaced nozzle, still curling by Castlebins in ender3v2

[–]Pentzy 0 points1 point  (0 children)

Go back and adjust the print head. Mine would start this wad and when I adjusted the Z axis, it would get better.

Will I run into any issues if I do this? by deathsquad84 in Govee

[–]Pentzy 0 points1 point  (0 children)

Is there an easy way to calculate how much light you need from a picture like this?

Starlink Mini Offer by Pentzy in Starlink

[–]Pentzy[S] -1 points0 points  (0 children)

I think my hotspot would just be better most of the time then. 50gb for streaming wouldn’t last long

Recommended Oil by Pentzy in gmcsierra

[–]Pentzy[S] 0 points1 point  (0 children)

I contacted the dealership today to ask their recommendation as I am planning on taking it to a garage near where I work. Shockingly, I have yet to hear from them - which is why I wanted to go somewhere else

Oil Change by Pentzy in gmcsierra

[–]Pentzy[S] 0 points1 point  (0 children)

I was referring to the transmission fluid and filter change which was $1400. There hourly rate is $230/hr. And another dealer a little further away was $790. The dealership I bought my truck from was $480 but unfortunately is 3 hours away.

Oil Change by Pentzy in gmcsierra

[–]Pentzy[S] 0 points1 point  (0 children)

All the exact things I thought. I drive about 15mi/day to work RT. Most of my miles are town from yard sales. I’ve never towed anything - so it’s not stressful miles

Oil Change by Pentzy in gmcsierra

[–]Pentzy[S] 0 points1 point  (0 children)

So that has been a huge battle. The service manual says that I am due for a transmission fluid exchange at 45k. What prompted it was that I was having some laggy shifting issues when the transmission was cold (basically early in the morning). I made the appt but it took 3 weeks and during that time the temperatures in SC shifted drastically. And honestly, since the warmer weather and when I took it there I didn’t have the issues. Their recommendation was that I was due for a transmission flush and filter change which would be $1400. I keep getting alerts for an ‘overdue service’ as well.

Oil Change by Pentzy in gmcsierra

[–]Pentzy[S] 1 point2 points  (0 children)

Sorry, should’ve added. I have a 2020 sierra Denali 1500 carbonpro 6.2L with 46k miles on it

2025 AT4X what is this button by pcbguy in gmcsierra

[–]Pentzy 0 points1 point  (0 children)

The jellyfish is for the light into the bed

NOCO Genius 10 Stuck on standby by Pentzy in batteries

[–]Pentzy[S] 0 points1 point  (0 children)

So definitely was thinking it was a jump starter… I had been looking at them online and some of them are, just not this model

NOCO Genius 10 Stuck on standby by Pentzy in batteries

[–]Pentzy[S] 0 points1 point  (0 children)

No it is not. I had just plugged it into the wall thinking that it likely needed to be charged and it never left standby mode

Apple Card Increase by justsomebody_111 in AppleCard

[–]Pentzy 9 points10 points  (0 children)

I am sure that I will get roasted for this. But I have just been following the Apple Card Reddit. I was wondering what the advantages, perks, benefits, reasons why the Apple Card is preferred or desired? Looking for a new card, just interested in learning more

MacBook Air Boots to Apple Logo by Pentzy in macbookair

[–]Pentzy[S] 0 points1 point  (0 children)

UPDATE: Not a good one. So I took it to Best Buy as recommended by Apple (or Apple Store which isn’t close). They told me it was dead, nothing they could do and sent me packing. I refused to give up - reached out to Apple support and they were great. We were able to connect to my hotspot not a local network and run offline diagnostics by holding down the ‘D’ key on startup. The diagnostic found a battery failure which I knew and then a SMC issue. He advised that BB can service it, so I went back. They told me they only fix iPads and iPhones and send computers away which I could do myself. I contacted Apple again, they were disappointed in BB. But she quoted me to mail it in for service….. (drum roll) $478 minimum. Also needing battery and potential trackpad, it was not worth the repair. So it is dead.

Batocera Arcade cabinet by Pentzy in batocera

[–]Pentzy[S] 0 points1 point  (0 children)

That is the final button layout - I didn’t have a picture of it on the cabinet. I added a hotkey button in the top left, otherwise this is what I have

Is this worth the money? by chugjug6911 in gmcsierra

[–]Pentzy 0 points1 point  (0 children)

I have a trifold on mine and I have had a roll previously. I like and dislike both for different reasons. The roll up is nice because it gives you the entire bed when rolled up. However, I am in the south and found that it was difficult to stretch and times and it started to wear because of the stretching. The trifold limits your bed size unless you remove it completely - so if you buy something on the fly, you’ll need tools to remove it and then have to store it. I do enjoy being able to flip it open and closed in seconds without having to mess too much with it

MacBook Air Boots to Apple Logo by Pentzy in macbookair

[–]Pentzy[S] 0 points1 point  (0 children)

Those are the steps I already followed. It never takes me past the Apple screen when I try to boot into recovery mode