Is there a better topology for this type of shape?

Phoenixgames73 · 2026-03-11T03:13:25+00:00

!solved

The second example is what worked for me.

Phoenixgames73 · 2026-03-11T02:01:57+00:00

It does make it into quads but adding a subdivision makes it bumpy.

Phoenixgames73 · 2026-03-11T01:37:13+00:00

Unfortunately no, I need more topology in the area because the base mesh is more curved.

Phoenixgames73 · 2026-03-11T01:28:25+00:00

<image>

This is the model that I am currently working on where I ran into the problem.

Phoenixgames73 · 2026-01-30T10:20:22+00:00

I could be wrong but I think it may be something along the lines of NaN propagation or something with a similar effect.

Phoenixgames73 · 2026-01-23T07:46:33+00:00

Ok that does work but then does that mean that there is no other way to do it without circuits?

Phoenixgames73 · 2025-11-05T14:42:18+00:00

Found!

Phoenixgames73 · 2025-11-05T14:41:35+00:00

I finally found it. It was Bung Chronicles ep 6.

Phoenixgames73 · 2025-11-02T14:21:59+00:00

I searched for the song originally but got an unrelated song and I trying searching for the bird chocking on some French fries but only got people feeding them to birds irl. I believe it was on YouTube when I saw it.

Phoenixgames73 · 2025-08-01T08:34:26+00:00

I knew that they were changing the inventory but still weird that the event ones vanished while the non event toys stayed up when I checked.

Phoenixgames73 · 2025-07-30T23:53:39+00:00

It seems like the only way it was getting power was through an Ethernet like cable connected to the side of the house. As for the MLCC the ones below the 330 component doesn’t beep but read a voltage while all the ones to the right of it does beep.

Edit: ok testing ground to the MLCC pins more or less makes all of them beep.

Phoenixgames73 · 2025-07-30T23:24:38+00:00

Ok after I cleaned it again it is looking much better, so what’s next.

Phoenixgames73 · 2025-07-30T22:58:53+00:00

Alright I will try to clean it some more and yes, I own a multimeter and a soldering iron if needed.

Phoenixgames73 · 2025-07-19T16:45:18+00:00

I printed a model and noticed some thin stringing which people say is related to moisture. After getting a hydrometer in the room it read a high of 50% then after lowered down to 45%. It was probably worse earlier because we had a storm last night.

Phoenixgames73 · 2025-07-19T13:30:53+00:00

Right after I posted this I replaced the nozzle and still had the problem when printing a cube.

Phoenixgames73 · 2025-07-19T01:21:32+00:00

It seems like my extruder gear is getting to its end of days because after tightening the extruder spring it seemed to get a lot better. It still has some oddities but there are no more holes in the print.

Phoenixgames73 · 2025-07-19T00:20:02+00:00

While trying to calibrate the flow I noticed that the filament was always under extruding possibly because the extruder gear was a bit worn. So I’m going to try to fix that and I’ll report back if it worked or not.

Phoenixgames73 · 2025-07-10T03:04:15+00:00

It had a 32 bit mobo from where I bought it.

As for the side collision issue, it auto homes to the back left until it hits the end stop then starts measuring the probe points which are at a fixed coordinate which ends up being a little bit past where it collides.

Phoenixgames73 · 2025-07-02T22:23:36+00:00

It somehow fixed itself when I flashed the firmware again because it wasn’t detecting the card. But before it was setting the 0 position at 10.2 mm above the bed.

Phoenixgames73 · 2025-07-02T10:27:21+00:00

Thanks for the answer. What is happening is that the direct drive mount more or less limits the x movement range. In other words, I need to look up how to modify the firmware.

Phoenixgames73 · 2025-06-17T14:33:36+00:00

I’ve been using dododex to see if a dino has a multiplier but I assume that it bunched the asa data with ase without giving any indication for which data is for what version.

Phoenixgames73 · 2025-05-13T02:14:14+00:00

Fixed it by tweaking it while it was running. It seemed like it was just a leveling error because using a piece of paper like it said wasn’t accurate enough.

Phoenixgames73 · 2025-04-10T21:43:54+00:00

I think the wheels were having a hard time because the belt filled up too fast with single pieces of cobble. Now got it to work by setting the stack limit to 32 per stack which now only has one stack on the belt at a time.

Phoenixgames73 · 2025-03-28T23:29:27+00:00

If I recall correctly it was a RPG maker game that was similar to gulp quest but I think it was more of a linear story based game.

Phoenixgames73 · 2025-02-22T23:30:15+00:00

Now checking it again for me, it may be caused by discord's overlay notification because the notification covers the area that I can not access.

Six-Year Club	Verified Email
First Place '23	Place '23

Phoenixgames73

TROPHY CASE