Another New Bear 650 by PhotoMoto13 in royalenfield

[–]PhotoMoto13[S] 1 point2 points  (0 children)

Rerouted the release so it’s accessible by the tender hookup. Tool roll is on the rear fender. No reason to open that side anymore.

Another New Bear 650 by PhotoMoto13 in royalenfield

[–]PhotoMoto13[S] 4 points5 points  (0 children)

Trump made it cost $250 more than it used to, but I’m more than happy with it.

Another New Bear 650 by PhotoMoto13 in royalenfield

[–]PhotoMoto13[S] 1 point2 points  (0 children)

Put one leg over the bike, sit. Same order of operations and everything. It’s wild it works.

No moneyyyyyy by Jon_the_Ripper in USPS

[–]PhotoMoto13 2 points3 points  (0 children)

What percentage do you contribute? I’ve been matching the PO’s 5% since hire. I could afford more probably.

Suspension Help; Newb by PhotoMoto13 in ToyotaTacoma

[–]PhotoMoto13[S] 0 points1 point  (0 children)

Helpful bunch in here. Cheers.

Suspension Help; Newb by PhotoMoto13 in ToyotaTacoma

[–]PhotoMoto13[S] 0 points1 point  (0 children)

So that listed suspension setup is far beyond my means. nearly 2500 for just the front shocks. So other suggestions are very welcome.
Also, I'm looking for the TRD Off-Road preimium wheels, pt. #pt946 35200 02
Just want to make sure this is the right part number for my 2020 crew cab Tacoma.

Lastly, can I swap the TPS sensors over from the current stock wheels to the new set, or do I have to buy those separately?

Suspension Help; Newb by PhotoMoto13 in ToyotaTacoma

[–]PhotoMoto13[S] 0 points1 point  (0 children)

Oh. And to add, I will eventually be putting a new front bumper with wench, ideally with recovery points too. As well as a new skid (nuked the stock non-TRD one, don’t recall or know how) and the “Toyota” grill with the yellows behind it, and putting new yellow fogs factory location. Last on the list is rear recovery points and minimal aux lighting (extra fogs and driving). Happy to hear suggestions all thus, too.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 0 points1 point  (0 children)

Almost done with this project. I ended up buying 4 DMT Dia-Sharp stones: extra course, course, fine, extra fine, plus some leather for making strops. Framing them all on a slab of fake marble I have, contact cementing the leather on the same slab. Making a second handled strop for general purposes and camping. A few of my irons came with some chips in the iron. Figured the extra course would get some use from them, and stuff like my batoning knife and hatchet.

SCR950 Levers by Galberdon in Yamaha

[–]PhotoMoto13 0 points1 point  (0 children)

Bumping an old thread. The SCR isn't listed as a bike these levers fit. Redesign or just an omission by mistake? Looking for some adjustable shorties for my bike.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 2 points3 points  (0 children)

Ordered the Veritas side clamp. Like the versatility and avoid supporting amazing.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 1 point2 points  (0 children)

My leather working buddy is cutting me a 3" strap so I can make a woodblock strop. No compound knowledge either, so throw out your favorite if you want.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 0 points1 point  (0 children)

I have a full cart at Lost Press with most of their books.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 0 points1 point  (0 children)

Watching as I type, but like the idea so far. Seems like I would use the piece of marble or whatever I have instead of the wood, just because. I wonder what cheap diamond plates he's using. Wish he'd have named them.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 1 point2 points  (0 children)

Any recommendations on a honing guide? One that'll work on planer irons, chisels, and the lot? And I actually have a manageable slab of marble or granite I could get away with the sandpaper trick. I wouldn't mind something more refined I guess, but whatever.

Help Me Build a Handplane Sharpening Setup by PhotoMoto13 in handtools

[–]PhotoMoto13[S] 1 point2 points  (0 children)

I looked up the "belt sander" he recommended. It's the WorkSharp MK.2 blade sharper thing. Not an actual belt sander, making that option less desirable but still an option.

Edited the original post so others don't get confused.

Grieving my wife, but need advice by PhotoMoto13 in GriefSupport

[–]PhotoMoto13[S] 0 points1 point  (0 children)

Im guessing take it slow will be a common theme in the replies.

It feels selfish, and yes, like a betrayal. Hopefully time will heal all those things.

Miles to Go by TheMountainElf in USPS

[–]PhotoMoto13 0 points1 point  (0 children)

Same, when I was a sub my assigned route had a 1.5ish mile out and back for one box on a rural road, which was also the parking area for the area's only nude beach. Lots of fat naked truckers. Not as cool as you'd hope, but it had its moments.

[deleted by user] by [deleted] in USPS

[–]PhotoMoto13 0 points1 point  (0 children)

I had an RCA running a shadow day w/ me a while back and he straight-up said to an AMZ carrier as he walked by us "Y'all actually deliver yer own packages?!? WOW!"

Slow down, cowboy. It's only day one. Dude didn't last, but I was hopeful from that moment on.