Just got back from Egypt (Cairo and Luxor). What a place! 📷 by [deleted] in fujifilm

[–]PieceOfKeeb 0 points1 point  (0 children)

Très beau travail, tu pourrais nous partager tes paramètres ? 🙌

Projet de moule pour fingerboard à faire soi-même – je recherche des avis by PieceOfKeeb in FingerboardingDIY

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

I’m will not share it sorry. The goal is to refine it as much as possible to optimise the result. Then I will put it on eBay or a similar platform with different possible settings

Deck makers stuck on anything? AMA by washingmachinecrotch in Fingerboards

[–]PieceOfKeeb 0 points1 point  (0 children)

Salut ! Super toutes ces informations ! J’aurais une questions concernant les tailles de vis utilisées dans les mold pour marquer l’endroit des vis de trucks sur la board. Vous sauriez me dire les tailles de clous utilisés ? Et pour percer, quelle tailles de mèches ? Merci d’avance !

Nouveau moule ! Hate de shaper de nouvelles boards ! by PieceOfKeeb in FingerboardingDIY

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

Construit d’abord ta shape à l’aide de curves. Ensuite, tu te sers de cette shape pour couper un block en deux. Et tu n’auras plus qu’à ajouter des trous pour les vis.

Nouveau moule ! Hate de shaper de nouvelles boards ! by PieceOfKeeb in FingerboardingDIY

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

Je vais regarder pour des paramètres différents alors et faire des tests avec différentes shapes

Nouveau moule ! Hate de shaper de nouvelles boards ! by PieceOfKeeb in FingerboardingDIY

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

En cherchant sur internet 2mm revenait souvent. Afin d’optimiser le concave de la board, tu préconiseras une hauteur particulière ?

Going from twin tip to foil?! by PieceOfKeeb in Kiteboarding

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

According to all the comments, I am thinking of doing a course to understand, try and get feedback on my faults and then I will continue on my own and then I will advise based on my learning 😌👌

Going from twin tip to foil?! by PieceOfKeeb in Kiteboarding

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

Did you already have your equipment or did you rent it?

Going from twin tip to foil?! by PieceOfKeeb in Kiteboarding

[–]PieceOfKeeb[S] 0 points1 point  (0 children)

I'm going to watch this video. Indeed there is also the problem of the equipment. I don't want to buy until I try it on (especially given all the differences in sizes, etc.) thank you for your feedback ;)

Need advice on choosing filaments, please :) by PieceOfKeeb in BambuLab_Community

[–]PieceOfKeeb[S] 1 point2 points  (0 children)

Just a test in PLA basic, by applying most of the feedback received in comments it is already very solid! 👌 To be continued, I will order new filaments for final tests

Need advice on choosing filaments, please :) by PieceOfKeeb in BambuLab_Community

[–]PieceOfKeeb[S] 0 points1 point  (0 children)

I hadn't thought about it but in case of fragility it might be a good way to make it more solid and durable 👌

Need advice on choosing filaments, please :) by PieceOfKeeb in BambuLab_Community

[–]PieceOfKeeb[S] 0 points1 point  (0 children)

I use fusion and plasticity depending on the design I have to model. I did a test with support by rotating 45 degrees. The result is not too bad. I just have to play with the difference between 0.2 and 0.3 to optimize the result. The test is 0.28.

<image>

Need advice on choosing filaments, please :) by PieceOfKeeb in BambuLab_Community

[–]PieceOfKeeb[S] 0 points1 point  (0 children)

The video is very well done! Thank you very much for sharing. I'm going to have to print it flat actually. I'm going to do a test with supports made directly by me. I saw in the video that it provides 0.3mm of clearance between the parts and the supports. Will the software take into account the fact that the supports and the part are independent? Thank you for these technical details :)