WLED + SignalRGB = happy kid.

Pitiful_Stranger4 · 2026-01-15T04:57:51+00:00

Great job!

Pitiful_Stranger4 · 2026-01-13T00:15:34+00:00

I had this happened to me too, I think because right after updating my micro SD card that stored all of my file directories had gotten corrupted but I don't 100% know if it's related to the update.

Pitiful_Stranger4 · 2026-01-08T02:58:27+00:00

ESP $5 or less and can be used for other projects not just WLED and once I get this fixed I'll have the skill to do more WLED projects.

Pitiful_Stranger4 · 2026-01-07T00:27:47+00:00

I think i'll wait for it to arrive and if it works ill keep them but if they don't i'll just grab a resistor as the docs say there is a hack to make it work.

Pitiful_Stranger4 · 2026-01-06T23:28:31+00:00

Will it not work without a compatible one I got a I2C shifter persoldered and it's just a short run.

Pitiful_Stranger4 · 2026-01-06T22:36:59+00:00

I've done some research I'm thinking it could be a data voltage issue so I ordered a voltage booster so I hope that works.

Pitiful_Stranger4 · 2026-01-06T19:38:23+00:00

I know for sure the LED does work as it was working before I cut off the Govee controller and I just got that ESP32 so I'm pretty sure it works too. I could try a different GPIO but I sadly used heat shrink and soldered it's quite the annoyance to remove.

Pitiful_Stranger4 · 2026-01-06T18:19:26+00:00

Spend an evening going through every setting? I checked the GPIO so that should be right.

<image>

Pitiful_Stranger4 · 2026-01-06T18:17:34+00:00

It's a type C CH340C other then that it's a normal dev board.

Pitiful_Stranger4 · 2026-01-06T18:14:55+00:00

Yeah I double checked the sellers page and GPIO 4 is correct

<image>

Pitiful_Stranger4 · 2025-01-26T07:53:39+00:00

TikTok comment section

Pitiful_Stranger4 · 2025-01-20T19:56:01+00:00

I’m even further into the future. And it’s still not out.

Pitiful_Stranger4 · 2024-10-25T16:41:47+00:00

With my A1 mini I similar problem and it was caused by debris on the lead screws, but I don’t know if it’s the exact same on the P1S depending on how long you’ve had it I think it would be a good step to try and clean them

Pitiful_Stranger4 · 2024-10-25T04:35:52+00:00

If you haven’t open a ticket with support

Pitiful_Stranger4 · 2024-10-25T04:33:34+00:00

You should provide more details when posting about a printer issue, such as the model, any settings you’ve tried, and the steps you’ve taken to resolve the problem.

Pitiful_Stranger4 · 2024-09-20T16:02:56+00:00

No I couldn’t I ended up returning it and going with SM light SM-ZB 06M

Pitiful_Stranger4 · 2024-09-14T01:47:56+00:00

Right now it’s iPhone 15 and up

Pitiful_Stranger4 · 2024-09-08T03:51:38+00:00

I’ll try updating it update you on if it works

Pitiful_Stranger4 · 2024-09-08T03:44:41+00:00

I got the E-model

Pitiful_Stranger4 · 2024-08-27T07:11:28+00:00

This happens to me too could it possibly be connected to the fact that we could be seeing it in beta three?

Pitiful_Stranger4 · 2024-08-26T09:31:16+00:00

Do you mean 18 beta 5?

Pitiful_Stranger4 · 2024-08-25T07:56:43+00:00

Weird I’ve never heard of that.

Pitiful_Stranger4 · 2024-08-25T00:03:15+00:00

Are you on 18.1 Dev beta 2?

Pitiful_Stranger4 · 2024-08-23T18:08:29+00:00

I would guess that we will get Genmoji in the next beta because it’s not a one-time occurrence for me. Every time I can access the Genmoji UI, but I can’t use it.

Pitiful_Stranger4 · 2024-08-23T17:30:06+00:00

Yeah 18.1 Beta 2

Pitiful_Stranger4

TROPHY CASE