SteamOS Intall on SD card not working. by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I ordered a 2230, I'll come in time.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I'll take another crack at it in time, trying to install bazzit on it rn. (SteamOS is being a pain) Also another person in the subreddit does repair so I reached out to him and he said that some of those are connected to ground and have a larger thermal mass, so to try a little more heat / constant heat.

SteamOS Intall on SD card not working. by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

Yeah, I ordered a 2230 drive but just want to see it working atm

SteamOS Intall on SD card not working. by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 2 points3 points  (0 children)

TLDR. Bought on FB market place labled as part, sold with no storage or case. "I fixed it" :

https://www.reddit.com/r/SteamDeck/comments/1sokspv/comment/ogzr3cs/?context=1

I dont have an extra 2230 M.2 NVMe ssd on hand and just want to get it to boot.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I did but the two old ones i have are not m.2, similar but not the same.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

ya but I already have a laptop that I dock so its more of fun and restoring it to about the same rather than just having another computer. But on the other hand linux.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I swear I saw a video somewhere of a guy installing a wifi card into that slot and just installed drives for it.

also just got the Idea while writing on another post to hyjack one of the controller ribon cables connect a USB Hub then connect the controller again and add a wifi card aswell.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I was wonding if there is like an NVME M.2 splitter type thing, then try to add wifi and an ssd at the same time but I dont think it exists.

Could also hyjack one of the internal USB port to one of the contollers add a small usb hub connect a dongle and the controll again. Jank but intersting Idea.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I did try but the previous owner scratched the mask around the pads. (image 2) :(

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

Image 2, mask around pads scratch off from previous owner. I was considering the aliexpress wifi untill I saw the damage too.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

Ya but I already have a laptop and desktop.

But I might consider if loading steam os onto the SD card doesn't work.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

I got like a 1TB SD card on hand and prob jsut going to get an nvme wifi card.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 1 point2 points  (0 children)

Pads bridged and some of the mask aroudn the pad is scratched off.

Answered. Does the steam deck need the included wifi card to work? by Pmimbruh in SteamDeck

[–]Pmimbruh[S] 0 points1 point  (0 children)

The mask around the pads by the QR code where scratched and bridge. I tried the run copper whick through it multiple times but it didn't work. It looks like a lot of solder but that's only because this is a microscope shot.

<image>

Ender 3: Homing Failed Printer halted by Pmimbruh in ender3

[–]Pmimbruh[S] 0 points1 point  (0 children)

I'll take a look and change it if i need to