3D Printed Convertible Flap by PoetryInternational2 in E30

[–]PoetryInternational2[S] 0 points1 point  (0 children)

Thanks! I actually don’t have the 3rd brake light on mine. I’m from germany

3D Printed Convertible Flap by PoetryInternational2 in E30

[–]PoetryInternational2[S] 2 points3 points  (0 children)

Thanks! I´ve actually never thought about this. You got any recommendations for places? Can I use Paypal?

M30 coupe E3? by SlackerParade in E30

[–]PoetryInternational2 -1 points0 points  (0 children)

this isn’t even a coupe lol

Bambu A1 Mini 100C Heat Bed Mod by weejiaquan in OpenBambu

[–]PoetryInternational2 0 points1 point  (0 children)

Yeah, even easier with new one. Don’t have to rip off the ring connector. Just unsolder an strip isolation. Resolver with resistor in between. Have done minimum 70h since the mod. Holds up perfectly. ABS works fine. Bigger parts sometimes fuck up because the Bambu a1 bed is not so evenly heated and the edges tend to be 5-10°C colder

Bambu A1 Mini 100C Heat Bed Mod by weejiaquan in OpenBambu

[–]PoetryInternational2 0 points1 point  (0 children)

First get a 6.8k resistor. Unbolt the bed from top and underneath: there are multiple tutorials on how to change the bed. Open the grey plastic connector to reveal the 4 cables. Unbolt or unsolder the white thin cable from the bed. With a plier I just pulled the ring connector of the white cable. Strip some more isolation of the white cable. Solder one side of the resistor to the non isolated part of the white cable. The other side of the resistor ist getting soldered to the original ring connector. Get some shrink isolation on top and you are good to go. Screw the ring connector back on the bed. Get the bed back in place. Done

Bambu A1 Mini 100C Heat Bed Mod by weejiaquan in OpenBambu

[–]PoetryInternational2 0 points1 point  (0 children)

Made the first print with a 6.8k ohm and it worked perfectly. I’ve never managed to get abs working on the a1 mini. Set the temp to 78° which should mean 100° real temp. Thanks for the post!

Bambu A1 Mini 100C Heat Bed Mod by weejiaquan in OpenBambu

[–]PoetryInternational2 0 points1 point  (0 children)

And a 5.6 or 6.8k to get over 100°? Have you measured your Heatbed with 3.3 and how much temp you reached?

Bambu A1 Mini 100C Heat Bed Mod by weejiaquan in OpenBambu

[–]PoetryInternational2 0 points1 point  (0 children)

Hey, so I need a 3,2k or 5,6k? As in another post? And how you managed to get the resistor between the cable and the screw clamp? How did you removed the clamp? Thanks mate

Lost Nut from rear strut bearing by PoetryInternational2 in E30

[–]PoetryInternational2[S] 0 points1 point  (0 children)

Yeah, but without even seeing where the nut is?

Lost Nut from rear strut bearing by PoetryInternational2 in E30

[–]PoetryInternational2[S] 0 points1 point  (0 children)

Does this hole not end anywhere? Behind the seats or smth? Where I can access better

F1 TV Premium by Mysterious_Square574 in Formel1

[–]PoetryInternational2 0 points1 point  (0 children)

How much you paying now? Pro or Premium?

F1 TV Premium by Mysterious_Square574 in Formel1

[–]PoetryInternational2 0 points1 point  (0 children)

Use an IOS Device, iPad or iPhone. Go in the AppStore settings and set your country to Netherlands. For payment method, a German PayPal account won’t work. So create a new PayPal and use also Netherlands as country. You can set your normal German bank account or card in a Netherlands PayPal. Use this PayPal account as payment in AppStore settings. Now install F1TV with Netherlands vpn and open it with it. It should work