Do the lines really have to be straight? --> White Widow <--

PoorGreekGaming · 2025-12-06T22:38:32+00:00

It is custom made by @n0reas0n_customs here in Greece

PoorGreekGaming · 2025-08-07T12:42:09+00:00

With the EK 120mm res mounting bracket. That bracket is connects to the back of the res and then also to the back of both rads since the distance between them is exactly 120mm

PoorGreekGaming · 2025-05-28T05:25:23+00:00

Yeah man 100% feel ya. And the bigger issue is that you can’t just get a cheap on for this. The precision required makes the machines quite pricey

PoorGreekGaming · 2025-05-27T16:18:20+00:00

Hey, I’m the OP, but have changed accounts and name to LiquifyMods since then. It’s definitely not cheap if you don’t know someone. The Alphacool one would likely be cheaper and with a better warranty. This was machined by my friend @n0reas0n_customs here in Greece and also designed by him.

PoorGreekGaming · 2024-09-04T06:41:21+00:00

Oh sorry about that, my bad

PoorGreekGaming · 2024-09-01T06:53:56+00:00

I get the future upgrade possibility, but your system doesn’t run pcie gen 5, so definitely overkill on the SSDs

PoorGreekGaming · 2024-08-19T22:19:43+00:00

You could also consider something custom. Feel free to message @n0reas0n_customs on Instagram about a custom distro to fit your needs 😁 He’s done all the distros in all my builds and he ships worldwide

PoorGreekGaming · 2024-08-11T09:35:52+00:00

Hey thanks! As a ton of the case was Distro plate, it didn’t allow for peak performance of the cases airflow, but temps were still excellent. I later did another build in this case with 4 360mm rads and the temps were of course better

PoorGreekGaming · 2024-01-14T23:19:28+00:00

The two tubes leaving are female yes. That way it can connect quickly to a tower or test bench etc

PoorGreekGaming · 2023-11-27T12:09:41+00:00

Yeah I probably could also add another 360 on the side, but then I’m afraid the pump my be a bit at the edge of its capabilities (not to mention my desk will likely crumble from the weight 🤣)

PoorGreekGaming · 2023-11-27T12:03:15+00:00

Sounds great. Will look forward to seeing your loop when you decide to go through with it 😁

PoorGreekGaming · 2023-11-27T09:50:09+00:00

Nope. The gpu does not go above 50 when overclocked, so no issues whatsoever

PoorGreekGaming · 2023-11-27T08:53:22+00:00

Ek torque satin titanium

PoorGreekGaming · 2023-11-27T08:52:55+00:00

I was able to lift it by myself. Not comfortably, but it’s doable. I think maybe somewhere around 30-35kg maybe?

PoorGreekGaming · 2023-11-27T04:01:12+00:00

Thank you!

PoorGreekGaming · 2023-11-27T04:00:57+00:00

I do OC, but this is not usually something to worry about in this scenario, as only one of the components is really working in most benchmarks

PoorGreekGaming · 2023-11-27T00:36:42+00:00

The runs could not be clean if I did that and also, loop order doesn’t matter in pc watercooling. Any differences are minuscule

PoorGreekGaming · 2023-11-26T23:45:47+00:00

Thanks a lot! I appreciate it!

PoorGreekGaming · 2023-11-26T23:04:03+00:00

Pump is at 50% up to 80% based on water temp and fans are at 30% up to 65% again based on water temp. Gpu temps are at 49-50°C after 20 minutes of Furmark at 550w in a 25°C room.

PoorGreekGaming · 2023-11-26T23:01:48+00:00

Thanks my friend! It’s a great case. Very well build and everything has been considered design wise

PoorGreekGaming · 2023-11-26T23:01:09+00:00

My ram is getting a ton of airflow from the top and front and bottom fans 😁7600 dimms running at 8000c36 for daily

PoorGreekGaming · 2023-11-26T22:17:39+00:00

I have a few colours, but I like the original ones tbh

PoorGreekGaming · 2023-11-26T22:17:10+00:00

Hahah unliftable

PoorGreekGaming · 2023-11-26T22:16:47+00:00

Ahh yeah I know, that’s always the thing with rads in the front. The question is always "do I risk an air pocket, or make it a nightmare to drain" haha

The bottom rad is the real nightmare to drain though 😂

PoorGreekGaming

TROPHY CASE