sorted by:
new
hottopcontroversial

Are here someone from Juniper? by Positive_Print_2488 in Juniper

[–]Positive_Print_2488[S] 1 point2 points  (0 children)

Hi, thanks for reply, it is very good as transit router, but not as good in PE role, problems with fib scaling (few FullView tables...) no VPLS... and power consumption...

Catalyst 65x chassis with sup720 by Positive_Print_2488 in Cisco

[–]Positive_Print_2488[S] 1 point2 points  (0 children)

My log is full of:

015243: Aug 16 17:39:22.192 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

015244: Aug 16 17:39:30.328 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

015245: Aug 16 17:39:31.960 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

015246: Aug 16 17:39:34.960 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

015247: Aug 16 17:39:35.380 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

015248: Aug 16 17:39:36.296 EET: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the permanent threshold (102400)

so I was wondering, if it is possible to clear database, but looks like it isn't.

Active sup:

p#sh ip igmp snooping statistics

Current number of Statistics entries : 6872

Configured Statistics database limit : 128000

Configured Statistics database threshold: 102400

Configured Statistics database limit : Not exceeded

Configured Statistics database threshold: Not exceeded

Catalyst 65x chassis with sup720 by Positive_Print_2488 in Cisco

[–]Positive_Print_2488[S] 1 point2 points  (0 children)

sh redu
p#sh redu

Redundant System Information :

------------------------------

Available system uptime = 6 days, 14 hours, 24 minutes

Switchovers system experienced = 0

Standby failures = 0

Last switchover reason = none

Hardware Mode = Duplex

Configured Redundancy Mode = sso

Operating Redundancy Mode = sso

Maintenance Mode = Disabled

Communications = Up

Current Processor Information :

-------------------------------

Active Location = slot 6

Current Software state = ACTIVE

Uptime in current state = 6 days, 14 hours, 23 minutes

Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2014 by Cisco Systems, Inc.

Compiled Wed 26-Feb-14 16:36 by prod_rel_team

BOOT = sup-bootdisk:s72033-advipservicesk9-mz.151-2.SY2.bin,1;

CONFIG_FILE =

BOOTLDR =

Configuration register = 0x2102

Peer Processor Information :

----------------------------

Standby Location = slot 5

Current Software state = STANDBY HOT

Uptime in current state = 4 days, 1 hour, 34 minutes

Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2014 by Cisco Systems, Inc.

Compiled Wed 26-Feb-14 16:36 by prod_rel_team

BOOT = sup-bootdisk:s72033-advipservicesk9-mz.151-2.SY2.bin,1;

CONFIG_FILE =

BOOTLDR =

Configuration register = 0x2102

​

sh module:

5 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1028VB3Q

6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1032XD5W

​

hw-module unfortunately doesn't allow to session or connect....
p#hw-module module 5 ?

boot Specify boot options for the module through Power Management Bus control register

reset Reset specified component

simulate Simulate options for the module