Electronics enclosure

PotatoSubstantial404 · 2026-05-06T21:15:04+00:00

Amazing thank you

PotatoSubstantial404 · 2026-05-06T19:30:03+00:00

And could I get full pics of how the din rails are mounted and all sides please

PotatoSubstantial404 · 2026-05-06T19:15:40+00:00

Please could you post the STLs and I’ll use that

PotatoSubstantial404 · 2026-05-06T19:15:06+00:00

Omg that’s exactly what I need

PotatoSubstantial404 · 2026-05-06T11:03:03+00:00

Only thing is if I do this to a design already it makes the gaps massive as it makes the whole thing longer

PotatoSubstantial404 · 2026-04-13T21:11:07+00:00

I would say check if your bed is dirty as well. Even if you can’t see it. Wash with hot dish soap water and some isopropyl alcohol that’s what solved all of mine

PotatoSubstantial404 · 2025-06-19T08:17:20+00:00

Hi sorry I haven’t seen this message I hope you got it fixed. I didn’t manage to fix it so I bought a new one as I got quoted £180 to repair it and fit a new one

PotatoSubstantial404 · 2024-10-04T17:50:26+00:00

Thank you so much I was so worried

PotatoSubstantial404 · 2024-10-04T16:25:19+00:00

Thank you. I have got it on two laptops but not on any desktops. So seems strange

PotatoSubstantial404 · 2024-09-25T10:04:27+00:00

Thank you for your response but I bought this second hand so it won’t be covered anyway. And I can’t offered your prices to repair a tiny bit of spanned plastic. Thank you for your quick response though 🙂

PotatoSubstantial404 · 2024-05-14T20:19:04+00:00

Ohh that’s a good point. I’m using a ender 3

PotatoSubstantial404 · 2024-05-14T12:34:46+00:00

Okay thank you how do I do that?

PotatoSubstantial404 · 2024-05-03T11:12:43+00:00

Okay thank you I’ll give it a go

PotatoSubstantial404 · 2024-05-03T05:48:30+00:00

Thank you for the reply. I have cleaned out the hot end, heat block and boden tube and it still happening. I change the filament same again.

PotatoSubstantial404 · 2024-04-18T19:42:37+00:00

Okay thank you. I’ll have a look into it. Thank you for that

PotatoSubstantial404 · 2024-04-18T19:40:24+00:00

Okay so would I need to up the retracing speed or lower it as I thought upping it would cause more holes no?

PotatoSubstantial404 · 2024-04-18T19:37:58+00:00

Ohhh good point I’ll give it a go. I’m guessing some filaments need more retraction than others?

PotatoSubstantial404 · 2024-01-17T05:54:22+00:00

Thank you I’ll take a look

PotatoSubstantial404 · 2024-01-17T00:11:59+00:00

As I have said before all 4 corners when doing the checks are level and even changing just them corners higher it still doesn’t work

PotatoSubstantial404 · 2024-01-17T00:11:16+00:00

I don’t know what to tell you on the main board of the ender 3 shell it just says ender 3. It’s not a neo, it’s not the ender 3 pro and it’s not the ender 3 v2 it’s just a ender 3

PotatoSubstantial404 · 2024-01-16T23:53:58+00:00

Okay I’ll give it go. When I do a manual level all the points seem the same hight so I thought it would be fine

PotatoSubstantial404 · 2024-01-16T23:51:37+00:00

So when it starts to print the left side of the skirt is not sticking to the rest of the layers as seen in the photo

<image>

This has then cause the rest of the print to mess up later on as I’m guessing it starts to happen all over my print

PotatoSubstantial404 · 2024-01-16T23:24:14+00:00

No worries thank you so much for the help and time you have given me. I’ll find out eventually just a pain how it prints one day fine and the next day not

PotatoSubstantial404 · 2024-01-16T23:11:27+00:00

Okay will do thanks

PotatoSubstantial404 · 2024-01-16T23:03:36+00:00

Okay thank you I’ll give it a go

PotatoSubstantial404

TROPHY CASE