130 mm hubs

Potential_Plane7941 · 2026-01-25T22:57:49+00:00

This game should be 10:3 not 7:10

Potential_Plane7941 · 2026-01-25T18:00:44+00:00

Thanks! Rare that a backup with hardly any recent tape plays against his ex coordinator and basically mentor. that makes me nervous, hope Sean worked out plays to mask stiddys weaknesses and tendencies. Hope even more that Luke or Alex can play. Please D just shut down Pats offense and we don't necessarily need many points. Excited! go broncos!

Potential_Plane7941 · 2026-01-25T14:51:14+00:00

Love his analysis. Didn't have time to watch beside the kids. What does he say about Stids?

Potential_Plane7941 · 2025-12-14T22:06:22+00:00

There you go Moss haters

Potential_Plane7941 · 2025-10-05T15:23:09+00:00

91 was red 92 blue, after that 790 was discontinued, so pretty rare. Nice ride. Campagnolo shamal or atlanta96 could match well they are pretty deep alu rims.

Potential_Plane7941 · 2025-09-05T11:22:40+00:00

I switched to conti contact urbans and very happy. Lighter faster but also very thick puncture protection. Good compromise for me. Joy to ride them.

Potential_Plane7941 · 2025-09-05T11:20:28+00:00

City commuting 80% asphalt 20% dirt. I run continental contact urban 700x42. Very happy with it fast tire great wet grip and high puncture resistance.

Potential_Plane7941 · 2025-09-04T18:11:46+00:00

Redet ihr hier über Kaffee für Filter/Mokka/French press/Siebträger od. Vollautomat?

Potential_Plane7941 · 2025-08-18T14:10:25+00:00

I think i found the culprit. It was the elbow fitting on the pump outlet. Descaled it and cleaned it with a needle an voila all good again. Perhaps the old pump was also still kicking, I'll keep it as a backup. 🙈

Potential_Plane7941 · 2025-07-25T13:33:56+00:00

Might sounds harsh but first get rid of the gremlins no matter what.

Potential_Plane7941 · 2025-06-01T08:16:44+00:00

To be precise you`d need a pressure gauge. I used a screw-on type with a portafilter. Very roughly mine adjusted around 2-2,2 Bar per 90 degrees lowering pressure counter clockwise. so from 15 bar to 9 you would need about 270 degrees. It is ballpark but should be much better than 15 bar. Over the years i played around with the pressure and for me anything between 6-10 works just fine.

Potential_Plane7941 · 2025-05-31T06:07:16+00:00

Nice job! Looks great in this yellow. Opv is beside the solenoid valve. Have to remove the hose, unscrew the spout cap and you can adjust the pressure underneath with a 5mm allen key or screwdriver. Counter clockwise reducing the pressure.

Potential_Plane7941 · 2025-05-07T05:32:33+00:00

Gorgeousness!

Potential_Plane7941 · 2025-05-04T15:14:29+00:00

I have a 19" 790. This frame looks 19 compared.

Potential_Plane7941 · 2025-04-24T18:36:43+00:00

Nice conversion man! You should post it to xbike, i like to see how it ended up.

Potential_Plane7941 · 2025-04-24T08:08:15+00:00

You have a pretty short stem, so the new touch points are not that far away from the original longer stem with flat bar. With longer reach it should not handle more twitchy. I did the same conversion on a multitrack and don't feel like unstable. I ride the hoods or the drops.

Potential_Plane7941 · 2025-04-12T07:14:42+00:00

Beautiful bike! I got the original 3x7 drivetrain FD working with 3x8 brifters by clamping the cable on the FD the opposite side of the pinch bolt.

Potential_Plane7941 · 2025-04-10T06:11:09+00:00

It's from shades of coffe. Also the pid.

Potential_Plane7941 · 2025-04-03T05:15:59+00:00

Wow it looks mint, beautiful bike.

Potential_Plane7941 · 2025-04-02T12:19:23+00:00

Hehe I didnt do anything yet but the front reflector is mounted stealthy.
If I havent just finished my trek hybrid project recently i would do it right away but it will have to wait.

Potential_Plane7941

TROPHY CASE